Specification

Specifications table for model DP-M2A
ItemPerformance characteristics
CE Marking Directive ComplianceEMC Directive, RoHS Directive
Type of Pressure Differential pressure
Rated Pressure Range 0 to 2.00 kPa.D {0 to 204 mmH2O.D}
Set Pressure Range 0 to 2.00 kPa.D {0 to 204 mmH2O.D}
Set Pressure Resolution0.01 kPa.D {1 mmH2O.D}
Pressure Withstandability6 kPa.D {612 mmH2O.D}
Applicable FluidNon-corrosive gas
Selectable UnitskPa, mmH2O
Supply Voltage 12 to 24 V DC +10/-15% Ripple P-P 10 % or less
Current Consumption75 mA or less
Comparative OutputNPN open-collector transistor
・Maximum sink current : 100 mA
・Applied voltage : 30 V DC or less (between comparative output and 0 V)
・Residual voltage : 1 V or less (at 100 mA sink current)
0.4 V or less (at 16 mA sink current)
Comparative Output: Utilization CategoryDC-12 or DC-13
Comparative Output: Output OperationSelectable either normally open (NO) or normally closed (NC) by the key
Comparative output: Hysteresis0.01 kPa.D {1 mmH2O.D}
Comparative Output: RepeatabilityWithin ±1 % F.S.
Comparative Output: Response Time10 ms or less
Comparative Output: Short-Circuit ProtectionIncorporated
Analog Current OutputOutput current : 4 to 20 mA (from 0 to 1.96 kPa.D {0 to 200 mmH2O.D})
Zero-point : within 4 mA ± 1 % F.S.
Span : within 16 mA ± 3 % F.S.
Linearity : within ±1 % F.S.
Load resistance : 0 to 250 Ω
Display3 digit red LED display (Sampling rate : 4 times/sec. approx.)
Display: Displayable Pressure Range-0.05 to 2.10 kPa.D {-5 to 210 mmH2O.D}
Indicators: OperationOrange LED (lights up when the comparative output is ON)
Indicators: Pressure UnitRed LED (The indicator corresponding to the selected unit lights up during the sensing mode.)
Indicators: M1 SettingRed LED (blinks in the M1 setting mode)
Indicators: M2 Setting Red LED (blinks in the M2 setting mode)
Pollution Degree 3 (Industrial environment)
Ambient Temperature0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed),
Storage: -10 to +60 ℃ +14 to +140 ℉
Ambient Humidity35 to 85 % RH, Storage : 35 to 85 % RH
Voltage Withstandability1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation Resistance50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
Vibration Resistance10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
Shock Resistance100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Temperature Characteristics Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉
: within ±3 % F.S. of detected pressure at +25 ℃ +77 ℉
Pressure Port ø4.6 mm ø0.181 in resin pipe
(Note): For production before April 2015 : ø4.8 mm ø0.189 in
MaterialFront case : ABS, Rear case : ABS, LED display : Acrylic, Pressure port : PA
Cable0.18 mm2 4-core oil resistant cabtyre cable, 2 m 6.562 ft long
Cable ExtensionExtension up to total 100 m 328.084 ft (less than 10 m 32.808 ft when conforming to CE marking) is possible with 0.3 mm2, or more, cable.
Weight (Typ.)Net weight : 75 g approx., Gross weight : 135 g approx
RemarkWhere measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉.

Stock Check

Important

The service is owned, operated, controlled and managed by Panasonic's distributors.

For pricing, delivery and technical questions related to this service, please direct to them.

Panasonic assumes no responsibility for any dealings you may have with distributors.