Part Number List

Results 12
Models table for series Digital Fiber Sensor FX-100
Part No.DatasheetCE Marking Directive ComplianceSupply voltagePower consumptionOutputOutput:Output operationOutput:Short-circuit protectionExternal inputResponse timeSensitivity settingOperation indicatorDigital displayFine sensitivity adjustment functionTimer functionEmission amount setting functionInterference prevention functionAmbient TemperatureAmbient HumidityAmbient IlluminanceVoltage withstandabilityInsulation resistanceVibration resistanceShock resistanceEmitting element (modulated)MaterialConnection methodCable LengthWeight (Typ.)Accessory
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1.5 V or less (at 100 mA source current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
PNP non-contact input
- Signal condition
High: +4 V to +V DC (Sink current 0.5 to 3 mA)
Low: 0 to +0.6 V DC or Open
- Input impedance: 10 kOhm approx.
Emission frequency 1: 2.5 ms or less (factory default setting)
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2, 3 or 4)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1.5 V or less (at 100 mA source current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
PNP non-contact input
- Signal condition
High: +4 V to +V DC (Sink current 0.5 to 3 mA)
Low: 0 to +0.6 V DC or Open
- Input impedance: 10 kOhm approx.
Emission frequency 1: 2.5 ms or less (factory default setting)
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2, 3 or 4)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1.5 V or less (at 100 mA source current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
PNP non-contact input
- Signal condition
High: +4 V to +V DC (Sink current 0.5 to 3 mA)
Low: 0 to +0.6 V DC or Open
- Input impedance: 10 kOhm approx.
Emission frequency 0: 250 micro s or less (factory default setting)
Emission frequency 1: 450 micro s or less
Emission frequency 2: 500 micro s or less
Emission frequency 3: 600 micro s or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2 or 3)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting).
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1.5 V or less (at 100 mA sink current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
NPN non-contact input
- Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC(Source current 0.5 mA or less)
- Input impedance: 10 kOhm approx.
Emission frequency 1: 2.5 ms or less (factory default setting)
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2, 3 or 4)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1.5 V or less (at 100 mA sink current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
NPN non-contact input
- Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC(Source current 0.5 mA or less)
- Input impedance: 10 kOhm approx.
Emission frequency 0: 250 micro s or less (factory default setting)
Emission frequency 1: 450 micro s or less
Emission frequency 2: 500 micro s or less
Emission frequency 3: 600 micro s or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2 or 3)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting).
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1.5 V or less (at 100 mA sink current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
NPN non-contact input
- Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC(Source current 0.5 mA or less)
- Input impedance: 10 kOhm approx.
Emission frequency 0: 250 micro s or less (factory default setting)
Emission frequency 1: 450 micro s or less
Emission frequency 2: 500 micro s or less
Emission frequency 3: 600 micro s or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2 or 3)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting).
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1.5 V or less (at 100 mA sink current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
NPN non-contact input
- Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC(Source current 0.5 mA or less)
- Input impedance: 10 kOhm approx.
Emission frequency 0: 250 micro s or less (factory default setting)
Emission frequency 1: 450 micro s or less
Emission frequency 2: 500 micro s or less
Emission frequency 3: 600 micro s or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2 or 3)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting).
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 75 g approx.
FC-FX-1(Protection cover): 1 pc. (Note)
CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1.5 V or less (at 100 mA source current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
PNP non-contact input
- Signal condition
High: +4 V to +V DC (Sink current 0.5 to 3 mA)
Low: 0 to +0.6 V DC or Open
- Input impedance: 10 kOhm approx.
Emission frequency 0: 250 micro s or less (factory default setting)
Emission frequency 1: 450 micro s or less
Emission frequency 2: 500 micro s or less
Emission frequency 3: 600 micro s or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2 or 3)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting).
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 75 g approx.
FC-FX-1(Protection cover): 1 pc. (Note)
CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1.5 V or less (at 100 mA sink current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
NPN non-contact input
- Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC(Source current 0.5 mA or less)
- Input impedance: 10 kOhm approx.
Emission frequency 1: 2.5 ms or less (factory default setting)
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2, 3 or 4)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 75 g approx.
FC-FX-1(Protection cover): 1 pc. (Note)
CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
EMC Directive, RoHS Directive
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1.5 V or less (at 100 mA sink current)
Selectable either Light-ON or Dark-ON, at SET mode
Incorporated
NPN non-contact input
- Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC(Source current 0.5 mA or less)
- Input impedance: 10 kOhm approx.
Emission frequency 1: 2.5 ms or less (factory default setting)
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
2-point teaching / Limit teaching / Full-auto teaching
Orange LED (lights up when the output is ON)
4 digits (green) + 4 digits (red) LCD display
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
3-level + Auto setting (from production in December 2007)
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2, 3 or 4)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.