Head-separated Dual display Digital Pressure Sensor [For gas & liquid] DPC-L100 / DPH-L100

Models table for series Head-separated Dual display Digital Pressure Sensor [For gas & liquid] DPC-L100 / DPH-L100
Part No.	CE Marking Directive Compliance	Type of pressure	Rated pressure range	Pressure withstandability	Applicable Fluid	Supply voltage	Current consumption	Analog Voltage Output	Response time	Protection	Ambient Temperature	Ambient Humidity	Medium temperature range	Voltage withstandability	Insulation resistance	Vibration resistance	Shock resistance	Grounding method	Pressure port	Material	Connecting method	Cable	Cable Extension	Weight (Typ.)	Accessories	Remark	Set pressure range	Set pressure resolution	Display	Display : Displayable pressure range	Power consumption	Comparative Output: Output Operation	Comparative Output: Output Modes	Comparative Output: Hysteresis	Comparative Output: Repeatability	Comparative Output: Response Time	Comparative Output: Short-Circuit Protection	Inputs : Sensor head input	Operation indicator	Temperature characteristics	Cable Length
DPH-L113V	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	-0.1 to +1 MPa	2 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 70 ℃ -4 to +158 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +70 ℃ -4 to +158 ℉ (No dew condensation or icing allowed), Storage: -30 to +70℃ -22 to +158 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +70 ℃ -4 to +158 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently.
DPH-L114	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +10 MPa	20 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 125 ℃ -4 to +257 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +80 ℃ (Pressure port: -20 to +125 ℃ -4 to +257 ℉, No dew condensation or icing allowed), Storage: -30 to +100 ℃ -22 to +212 ℉ [e-CON connector (accesory): -20 to +75 ℃ -4 to +167 ℉ (Storage: -30 to +75 ℃ -22 to +167 ℉)]	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +125 ℃ -4 to +257 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently. Oil is used in the factory inspection process for models DPH-L114 and DPH-L154. There may be some residual oil inside the pressure port.
DPC-L101	EMC Directive, RoHS Directive		DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, double amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted: 10 to 150 Hz frequency, double amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	CN-66A-C2 (Connector attached cable 2 m 6.562 ft), Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.084 ft (less than 30 m 98.425 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPH-L133	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +3.5 MPa	7 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 70 ℃ -4 to +158 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +70 ℃ -4 to +158 ℉ (No dew condensation or icing allowed), Storage: -30 to +70℃ -22 to +158 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +70 ℃ -4 to +158 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently.
DPC-L101-P	EMC Directive, RoHS Directive		DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, double amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted: 10 to 150 Hz frequency, double amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	CN-66A-C2 (Connector attached cable 2 m 6.562 ft), Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.084 ft (less than 30 m 98.425 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPH-L113	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +1 MPa	2 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 70 ℃ -4 to +158 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +70 ℃ -4 to +158 ℉ (No dew condensation or icing allowed), Storage: -30 to +70℃ -22 to +158 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +70 ℃ -4 to +158 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently.
DPC-L101-J			DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted : 10 to 150 Hz frequency, amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions for three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.1 ft (less than 30 m 98.4 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPC-L101-P-J			DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted : 10 to 150 Hz frequency, amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions for three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.1 ft (less than 30 m 98.4 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPH-L154	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +50 MPa	75 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 125 ℃ -4 to +257 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +80 ℃ (Pressure port: -20 to +125 ℃ -4 to +257 ℉, No dew condensation or icing allowed), Storage: -30 to +100 ℃ -22 to +212 ℉ [e-CON connector (accesory): -20 to +75 ℃ -4 to +167 ℉ (Storage: -30 to +75 ℃ -22 to +167 ℉)]	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +125 ℃ -4 to +257 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently. Oil is used in the factory inspection process for models DPH-L114 and DPH-L154. There may be some residual oil inside the pressure port.

Models table for series Head-separated Dual display Digital Pressure Sensor [For gas & liquid] DPC-L100 / DPH-L100
Part No.	CE Marking Directive Compliance	Type of pressure	Rated pressure range	Pressure withstandability	Applicable Fluid	Supply voltage	Current consumption	Analog Voltage Output	Response time	Protection	Ambient Temperature	Ambient Humidity	Medium temperature range	Voltage withstandability	Insulation resistance	Vibration resistance	Shock resistance	Grounding method	Pressure port	Material	Connecting method	Cable	Cable Extension	Weight (Typ.)	Accessories	Remark	Set pressure range	Set pressure resolution	Display	Display : Displayable pressure range	Power consumption	Comparative Output: Output Operation	Comparative Output: Output Modes	Comparative Output: Hysteresis	Comparative Output: Repeatability	Comparative Output: Response Time	Comparative Output: Short-Circuit Protection	Inputs : Sensor head input	Operation indicator	Temperature characteristics	Cable Length
DPH-L113V	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	-0.1 to +1 MPa	2 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 70 ℃ -4 to +158 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +70 ℃ -4 to +158 ℉ (No dew condensation or icing allowed), Storage: -30 to +70℃ -22 to +158 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +70 ℃ -4 to +158 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently.
DPH-L114	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +10 MPa	20 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 125 ℃ -4 to +257 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +80 ℃ (Pressure port: -20 to +125 ℃ -4 to +257 ℉, No dew condensation or icing allowed), Storage: -30 to +100 ℃ -22 to +212 ℉ [e-CON connector (accesory): -20 to +75 ℃ -4 to +167 ℉ (Storage: -30 to +75 ℃ -22 to +167 ℉)]	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +125 ℃ -4 to +257 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently. Oil is used in the factory inspection process for models DPH-L114 and DPH-L154. There may be some residual oil inside the pressure port.
DPC-L101	EMC Directive, RoHS Directive		DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, double amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted: 10 to 150 Hz frequency, double amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	CN-66A-C2 (Connector attached cable 2 m 6.562 ft), Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.084 ft (less than 30 m 98.425 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPH-L133	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +3.5 MPa	7 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 70 ℃ -4 to +158 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +70 ℃ -4 to +158 ℉ (No dew condensation or icing allowed), Storage: -30 to +70℃ -22 to +158 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +70 ℃ -4 to +158 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently.
DPC-L101-P	EMC Directive, RoHS Directive		DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, double amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted: 10 to 150 Hz frequency, double amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	CN-66A-C2 (Connector attached cable 2 m 6.562 ft), Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.084 ft (less than 30 m 98.425 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPH-L113	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +1 MPa	2 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 70 ℃ -4 to +158 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +70 ℃ -4 to +158 ℉ (No dew condensation or icing allowed), Storage: -30 to +70℃ -22 to +158 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +70 ℃ -4 to +158 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently.
DPC-L101-J			DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted : 10 to 150 Hz frequency, amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions for three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.1 ft (less than 30 m 98.4 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPC-L101-P-J			DPH-L113V : -0.1 to +1 MPa DPH-L113 : 0 to +1 MPa DPH-L133 : 0 to +3.5 MPa DPH-L114 : 0 to +10 MPa DPH-L154 : 0 to +50 MPa (Note) : Values differ depending on a connected sensor head.			12 to 24 V DC ±10 % Ripple P-P 10 % or less				IP40 (IEC)	-10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH		500 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each (when panel mounting bracket is mounted : 10 to 150 Hz frequency, amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration in X, Y and Z directions for three times each			Enclosure : PBT (glass fiber reinforced), LCD display : Acrylic, Mounting threaded part : Brass (nickel plated), Switch part : Silicone rubber	Connector			Net weight : 25 g approx. (excluding connector attached cable), Gross weight : 140 g approx.	Pressure unit label: 1 set	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉. The values specified above are applied only to the controller.	[DPH-L113V] -1.177 to +1.177 MPa -12.00 to +12.00 kgf/cm² -11.77 to +11.77 bar -170.6 to +170.6 psi [DPH-L113] -1.070 to +1.070 MPa -10.91 to +10.91 kgf/cm² -10.70 to +10.70 bar -155.2 to +155.2 psi [DPH-L133] -3.74 to +3.74 MPa -38.1 to +38.1 kgf/cm² -37.4 to +37.4 bar -542 to +542 psi [DPH-L114] -10.70 to +10.70 MPa -109.1 to +109.1 kgf/cm² -107.0 to +107.0 bar -1552 to +1552 psi [DPH-L154] -53.5 to +53.5 MPa -545 to +545 kgf/cm² -535 to +535 bar -1980 to +7760 psi (Note) : Values differ depending on a connected sensor head.	DPH-L113V : 0.001 MPa DPH-L113 : 0.001 MPa DPH-L133 : 0.01 MPa DPH-L114 : 0.01 MPa DPH-L154 : 0.1 MPa (Note): Values differ depending on a connected sensor head.	4 digits +4 digits 3-color LCD display (Display refresh rate : 250 ms, 500 ms, 1,000 ms, selectable by key operation)	[DPH-L113V] -0.155 to +1.022 MPa -1.58 to +10.42 kgf/cm² -1.55 to +10.22 bar -22.4 to +148.2 psi [DPH-L113] -0.050 to +1.020 MPa -0.51 to +10.40 kgf/cm² -0.50 to +10.20 bar -7.2 to +148.0 psi [DPH-L133] -0.17 to +3.57 MPa -1.7 to +36.4 kgf/cm² -1.7 to +35.7 bar -24 to +518 psi [DPH-L114] -0.50 to +10.20 MPa -5.1 to +104.0 kgf/cm² -5.0 to +102.0 bar -72 to +1480 psi [DPH-L154] -2.5 to +51.0 MPa -25 to +520 kgf/cm² -25 to +510 bar -360 to +7400 psi (Note): Values differ depending on a connected sensor head.	Normal operation : 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD) : 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL) : 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current	NO / NC, selectable by key operation	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)(however, 2 digits when using psi unit)	Within ±0.2 % F.S.	5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	Input voltage range : 1 to 5 V DC (over rated pressure range)	Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator : Lights up when each comparative output is ON )	Within ±0.5 % F.S. (ambient temperature range based on +20 ℃ +68 ℉)	Total length up to 100 m 328.1 ft (less than 30 m 98.4 ft when conforming to CE marking) is possible with 0.3 mm², or more, cable.
DPH-L154	EMC Directive, RoHS Directive	Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa.	0 to +50 MPa	75 MPa	Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7	9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)]	20 mA or less	Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 125 ℃ -4 to +257 ℉) (including linearity, hysteresis and repeatability)	1 ms or less	IP67 (IEC)	-20 to +80 ℃ (Pressure port: -20 to +125 ℃ -4 to +257 ℉, No dew condensation or icing allowed), Storage: -30 to +100 ℃ -22 to +212 ℉ [e-CON connector (accesory): -20 to +75 ℃ -4 to +167 ℉ (Storage: -30 to +75 ℃ -22 to +167 ℉)]	35 to 85 % RH, Storage : 35 to 85 % RH	-20 to +125 ℃ -4 to +257 ℉	150 V AC for one min. between all supply terminals connected together and enclosure	100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure	10 to 2,000 Hz frequency, acceleration 200 m/s², in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :	1,000 m/s² acceleration in X, Y and Z directions three times each	Capacitor earth (Enclosure-supply terminal)	R1/4 male thread (throttle embeded)	Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7)	Connector	0.2 mm² 3-core heat resistant cabtyre cable 2 m 3.562 ft long	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Net weight : 100 g approx., Gross weight : 150 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently. Oil is used in the factory inspection process for models DPH-L114 and DPH-L154. There may be some residual oil inside the pressure port.

Head-separated Dual display Digital Pressure Sensor [For gas & liquid] DPC-L100 / DPH-L100

Part Number List