Specification

Specifications table for model LS-401P-C2
ItemPerformance characteristics
Operation Indicator Orange LED (lights up when output 1 and output 2 are ON)
Laser Emission IndicatorGreen LED (lights up during laser emission)
Ambient Temperature-10 to +55 ℃ +14 to +131 ℉ (If 4 to 7 units are mounted close together: -10 to +50 ℃ +14 to +122 ℉ , if 8 to 16 units are mounted close together: -10 to +45 ℃ +14 to +113 ℉ )
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
Ambient Humidity35 to 85 % RH, Storage: 35 to 85 % RH
Voltage Withstandability1,000 V AC for one min.
between all supply terminals connected together and enclosure
Insulation Resistance20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration Resistance10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
Shock Resistance98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
MaterialEnclosure: Heat-resistant ABS
Transparent cover: Polycarbonate
Push button switch: Acrylic
Jog switch: ABS
Cable0.15 mm2 5-core cabtyre cable, 2 m 6.562 ft long
Weight (Typ.)Net weight: 65 g approx
Gross weight: 75 g approx
Supply Voltage 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Current ConsumptionNormal operation: 950 mW or less (Current consumption 40 mA or less at 24 V supply voltage)
ECO mode: 780 mW or less (Current consumption 33 mA or less at 24 V supply voltage)
Outputs (Output 1, Output 2) PNP open-collector transistor
- Maximum source current: 100 mA (Note)
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1.5 V or less [at 100 mA (Note) source current]
(Note) 50 mA if 5 to 8 connector type amplifiers are connected in cascade , and 25 mA if 9 to 16 connector type amplifiers are connected in cascade.
Outputs (Output 1, Output 2): Output Operation Selectable either Light-ON or Dark-ON, with jog switch
Response Time80 micro s or less (H-SP), 150 micro s or less (FAST), 500 micro s or less (STD), 4 ms or less (U-LG) selectable with jog switch
Outputs (Output 1, Output 2): Short-Circuit ProtectionIncorporated
External Input (Laser Emission Halt Full-Auto Teaching/Limit Teaching)PNP non-contact input
- Signal condition
High: +4 V to +V DC (sink current 3 mA or less), Low: 0 to +0.6 V DC or open
- Input impedance: 10 kOhm approx.
Select Indicator Yellow LED
(lights up when either output 1 or output 2 is selected)
Mode Indicator RUN: Green LED
TEACH, L/D, TIMER, CUST, PRO: Yellow LED
Digital Display4 digit (green) + 4 digit (red) LED display
Sensitivity SettingNormal mode: 2-level teaching / Limit teaching / Full-auto teaching / Manual adjustment
Window comparator mode: Teaching (1-level, 2-level, 3-level) / Manual adjustment
Hysteresis mode: Teaching (1-level, 2-level, 3-level) / Manual adjustment
Differential mode: 5-level settings
Fine Sensitivity Adjustment FunctionIncorporated
Timer Function Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective.
Timer Function: Time 1 to 9,999 ms
Automatic Interference Prevention FunctionIncorporated
[Up to four sets of sensor heads can be mounted close together. (However, disabled when in H-SP mode)]
Cable ExtensionExtension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.

Stock Check

Important

The service is owned, operated, controlled and managed by Panasonic's distributors.

For pricing, delivery and technical questions related to this service, please direct to them.

Panasonic assumes no responsibility for any dealings you may have with distributors.