|CE Marking Directive Compliance||・Low Voltage Directive ： EN IEC 60947-5-2|
・EMC Directive ： EN IEC 60947-5-2
|Sensing Range ||30 m 98.425 ft|
|Sensing Object ||dia. 20 mm dia. 0.787 in or more opaque object (Completely beam interrupted object)|
(Note) If slit masks (optional) are fitted, an object as small as 3 x 6 mm 0.118 x 0.236 in can be detected.
|Repeatability (Perpendicular to Sensing Axis) ||0.2 mm 0.008 in or less|
|Supply Voltage ||24 to 240 V AC +10-15 % or 12 to 240 V DC +10-15 % Ripple P-P 10 % or less|
|Power Consumption||Emitter: 1.5 VA or less|
Receiver: 2 VA or less
|Output||Relay contact 1 c|
- Switching capacity: 250 V AC 1 A (resistive load), 30 V DC 2 A (resistive load)
- Electrical life: 500,000 or more switching operations (switching frequency 3,600 operations/hour), 100,000 or more switching operations (switching frequency 3,600 operations/hour)
- Mechanical life: 100 million or more switching operations (switching frequency 36,000 operations/hour)
|Output: Output Operation ||Dark-ON|
|Response Time||10 ms or less|
|Operation Indicator ||Red LED (lights up when the output is ON)|
|Stability Indicator||Green LED (lights up under stable light received condition or stable dark condition)|
|Power Indicator ||Red LED (lights up when the power is ON)|
|Automatic Interference Prevention Function||-|
|Pollution Degree ||3 (Industrial environment)|
|Ambient Temperature||–20 to +55 ℃ –4 to +131 ℉ (No dew condensation or icing allowed) (Note),|
Storage: –30 to +70 ℃ –22 to +158 ℉
(Note):In case the sensor is to be used at an ambient temperature of –15 ℃ +5 ℉, or less, please contact our office.
|Ambient Humidity||35 to 85 % RH, Storage: 35 to 85 % RH|
|Ambient Illuminance||Incandescent light: 3,500 Lx or less at the light-receiving face|
|Voltage Withstandability||1,500 V AC for one min. between all supply terminals connected together and enclosure,|
1,500 V AC for one min. between power supply and output terminals,
1,000 V AC for one min. between relay contact terminals
|Insulation Resistance||20 MOhm , or more, with 500 V DC megger between power supply and output terminals, and between relay contact terminals|
| Vibration Resistance||10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions two hours each|
|Shock Resistance||500 m/s2 (50 G approx.) in X, Y and Z directions three times each|
|Emitting Element||Infrared LED (modulated)|
|Emitting Element: Peak Emission Wavelength||880 nm 0.035 mil|
|Cable||0.3 mm2 5-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long|
|Cable Extension||Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable (both emitter and receiver).|
|Impulse withstand voltage||2.5kV|
|Output minimum operational current||DC5V 1mA or more|
|Turn on time / Turn off time||10ms / 10ms|
Note : Turn-On time and Turn-OFF time are the delay time between reference sensor and measurement sensor in case round plate rotates as below.
|Maximum response frequency||50Hz|
Note:The maximum response frequency is the value calculated below.
Maximum response frequency = １ / (Turn on time＋Turn off time)
|Class of protection against electric shock||Out of classification|
|Note||Note 1 : Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.|
Note 2 : The output applied voltage should be the same as the supply voltage of the sensor.
Note 3 : Be sure to add a short-circuit protection (a fuse or a breaker) to the power supply input and the output..
In addition, use 3A or less fast blow fuse or breaker.