GP-XC5SE-P

GP-XC5SE-P design engineers Panasonic

Part No: GP-XC5SE-P

Specifications

ItemPerformance characteristics
[[Controllers]] TypePNP output
CE marking directive complianceEMC Directive, RoHS Directive
[[Controllers]] Supply voltage24 V DC plus or minus 10 % Ripple P-P 10 % or less
[[Controllers]] Current consumption150 mA or less
[[Controllers]] Resolution0.04 % F.S. (64 times average processing)
(Note) This value was obtained at a constant +25 ℃ +77 ℉ .
[[Controllers]] Sampling frequency40 kHz (25 micro s)
[[Controllers]] LinearityWithin plus or minus 0.3 % F.S.
(Note) This value was obtained at a constant +25 ℃ +77 ℉ .
[[Controllers]] Temperature characteristics0.07 % F.S./℃ or less
(Note) This value represents 20 to 60 % of the maximum sensing distance when combining the sensor head and controller.
[[Controllers]] Analog voltage outputsOutput voltage: -5 to +5 V (Note1) , Output impedance: 100 Ω approx.(Note2)
(Note1: Adjusted to a 0 to +5 V factory setting.)
(Note2:When using the BCD output unit GP-XBCD, the analog voltage output of a controller becomes invalid.)
[[Controllers]] Analog voltage outputs : Response time75 micro s (maximum speed)
[[Controllers]] Comparative outputs (HI, GO, LO)PNP open-collector transistor
-Maximum source current: 100 mA
-Applied voltage: 30 V DC or less
(between comparative output and +V)
-Residual voltage: 1.6 V or less (at 100 mA source current), 0.4 V or less (at 16 mA source current)
[[Controllers]] Comparative outputs (HI, GO, LO) : Utilization categoryDC-12 or DC-13
[[Controllers]] Comparative outputs (HI, GO, LO) : Output numberHI / GO / LO 3 value output
[[Controllers]] Comparative outputs (HI, GO, LO) : Output operationHI: ON when measured value > the upper limit value
GO: ON when upper limit value >= measured value >= lower limit value
LO: ON when lower limit value > measured value
[[Controllers]] Comparative outputs (HI, GO, LO) : Short-circuit protectionIncorporated
[[Controllers]] External inputPhoto-coupler input
- Input current: 9 mA or less
- Operating voltage: ON voltage 17 V or more (between 0 V and input), OFF voltage 4 V or less (between 0 V and input)
- Input impedance: 5 kΩ approx.
[[Controllers]] Serial I/ORS-232C
[[Controllers]] Zero-set setting methodPush button setting / External input setting
[[Controllers]] Indicators : MODEOrange LED (lights up when in mode status)
[[Controllers]] Indicators : HIOrange LED (lights up when the upper limit value is exceeded)
[[Controllers]] Indicators : GOGreen LED (lights up when within the upper and lower limit value)
[[Controllers]] Indicators : LOOrange LED (lights up when less than the lower limit value)
[[Controllers]] Indicators : TIMINGGreen LED (lights up as per the external or internal trigger timing)
[[Controllers]] Upper level digital display part5 digit orange LED (display of numerical values out of upper and lower limit value)
[[Controllers]] Lower level digital display part5 digit green LED (display of numerical values within the upper and lower limit value)
[[Controllers]] Pollution degree3 (Industrial environment)
[[Controllers]] Ambient temperature0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: 0 to +50 ℃ +32 to +122 ℉
[[Controllers]] Ambient humidity35 to 85 % RH, Storage: 35 to 85 % RH
[[Controllers]] Vibration resistance10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
[[Controllers]] Shock resistance100 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
[[Controllers]] MaterialEnclosure: Polycarbonate
[[Controllers]] WeightNet weight: 120 g approx.
[[Controllers]] AccessoryATA4811 (Controller mounting frame): 1 set
[[Sensor heads]] TypeNon-threaded type For 1 mm 0.039 in sensing
[[Sensor heads]] Sensing range0 to 1 mm 0 to 0.039 in
(Note) The sensing range is specified for the standard sensing object.
[[Sensor heads]] Standard sensing objectStainless steel (SUS304) / Iron sheet [Cold rolled carbon steel (SPCC)] 60 x 60 x t 1 mm 2.362 x 2.362 x t 0.039 in
[[Sensor heads]] Temperature characteristics0.07 % F.S./℃ or less
(Note) This value represents 20 to 60 % of the maximum sensing distance when combining the sensor head and the controller.
[[Sensor heads]] Pollution degree3 (Industrial environment)
[[Sensor heads]] ProtectionIP67 (IEC), IP67g (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil. Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
[[Sensor heads]] Ambient temperature-10 to +55 ℃ +14 to +131 ℉ , Storage: -20 to +70 ℃ -4 to +158 ℉
[[Sensor heads]] Ambient humidity35 to 85 % RH, Storage: 35 to 85 % RH
[[Sensor heads]] Voltage withstandability250 V AC for one min. between all supply terminals connected together and enclosure
[[Sensor heads]] Insulation resistance20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
[[Sensor heads]] Vibration resistance10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each
[[Sensor heads]] Shock resistance500 m/s2 acceleration (50 G approx.) in X, Y and Z directions five times each
[[Sensor heads]] EnclosureStainless steel (SUS303)
[[Sensor heads]] Cable protectorPP
[[Sensor heads]] Sensing partPAR
[[Sensor heads]] CableHigh frequency coaxial cable with connector, 3 m 9.843 ft long
(Note) For the flexible cable type, please contact our office.
[[Sensor heads]] Cable extensionExtension up to total 10 m 32.808 ft is possible with the optional cable.
[[Sensor heads]] Net Weight40 g approx.
(Note) The given weight of the threaded type sensor head is the value including the weight of the nuts and the toothed lock washer.
[[Sensor heads]] Accessories-

Parts InventoryParts Inventory

Searching inventory

The service is owned, operated, controlled and managed by Panasonic's distributors.

For pricing, delivery and technical questions related to this service, please direct to them.

Panasonic assumes no responsibility for any dealings you may have with distributors.

Related Documents

Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › Data sheetData Sheet
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-XGP-X
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-X5SEGP-X5SE
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-X5SEGP-X5SE
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-X5SEGP-X5SE
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-XCGP-XC
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-XCGP-XC
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-XCGP-XC
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-XC ControllerGP-XC Controller
Sensors › Factory Automation Sensors › Laser Measurement Sensors › High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor GP-X › GP-XC5SE-P › GP-XC5SE(-P)GP-XC5SE(-P)