HL-T1005A

HL-T1005A design engineers Panasonic

Part No: HL-T1005A

Specifications

ItemPerformance characteristics
TypeSensing width 5 mm 0.197 in type
CE marking directive complianceEMC Directive, RoHS Directive
Applicable controllerHL-AC1, HL-AC1P
Sensing range■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■
Sensing width:
ø1 mm ø0.039 in

Min. sensing object:
ø8 micro m ø0.315 mil opaque object

Repeatability (During the state in which light is half blocked):
4 micro m 0.157 mil
(Note:In case of an average sampling rate of 64 times.)

Linear output resolution:
4 micro m 0.157 mil
(Note) In case of an average sampling rate of 64 times.
(Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width.
(Note:This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.)


■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■
Sensing width:
ø1 to ø2.5 mm ø0.039 to ø0.098 in

Min. sensing object:
ø50 micro m ø1.969 mil opaque object
Repeatability (During the state in which light is half blocked): -

Linear output resolution: -
-
Beam widthn/a
Min. sensing objectn/a
Repeatability (During the state in which light is half blocked)n/a
Linear output resolutionn/a
Emission indicatorGreen LED (lights up during laser emission)
Interference prevention functionTwo units of sensors can be mounted close together. (When the controller interference prevention function is used)
Applicable sensor headn/a
Supply voltagen/a
Current consumptionn/a
Measuring cyclen/a
Linear outputn/a
Linear output : Temperature characteristicsn/a
Settable average sampling raten/a
Judgment outputs (HIGH, PASS, LOW)n/a
Judgment outputs (HIGH, PASS, LOW) : Utilization categoryn/a
Judgment outputs (HIGH, PASS, LOW) : Number of outputsn/a
Judgment outputs (HIGH, PASS, LOW) : Output operationn/a
Judgment outputs (HIGH, PASS, LOW) : Short-circuit protectionn/a
Laser OFF inputn/a
Zero reset inputn/a
Timing inputn/a
Reset inputn/a
Indicators : Laser emitting (LD ON)n/a
Indicators : Judgment outputsn/a
Indicators : Enable (ENABLE)n/a
Indicators : Zero reset (ZERO)n/a
Main digital displayn/a
Sub-digital displayn/a
Main functionsn/a
Pollution degree3 (industrial environment)
Environmental resistance : Ambient temperature0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉
Environmental resistance : Ambient humidity35 to 85 % RH, Storage: 35 to 85 % RH
Environmental resistance : Ambient illuminanceIncandescent light: 10,000 liter x or less at the light-receiving face
Voltage withstandability1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
Environmental resistance : Vibration resistance10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
Environmental resistance : Shock resistance300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Emitting element : IEC / JIS standards conforming typeRed semiconductor laser Class 1 (IEC / JIS)
(modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)
Emitting element : FDA regulations conforming typeRed semiconductor laser Class II (FDA)
(modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)
(IEC / JIS: Class 1)
MaterialEnclosure: Polyetherimide
Case cover: Polycarbonate
Front cover: Glass
Cable0.09mm2 3-core shielded cable with connector, 0.5 m 1.640 ft long
Cable extensionExtension up to total 10 m 32.808 ft is possible, with the optional cable.
I/O cablen/a
I/O cable extensionn/a
WeightEmitter: 15 g approx.
Receiver: 15 g approx.
AccessoryMS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver
CN-HLT1-1(Sensor head to controller connection cable): 1 cable
Laser beam alignment sticker: 2 pcs.
Label set (FDA regulations conformed type only): 1 set

Parts InventoryParts Inventory

Searching inventory

The service is owned, operated, controlled and managed by Panasonic's distributors.

For pricing, delivery and technical questions related to this service, please direct to them.

Panasonic assumes no responsibility for any dealings you may have with distributors.

Related Documents

Sensors › Factory Automation Sensors › Laser Measurement Sensors › Ultra-compact Laser Collimated Beam Sensor HL-T1 › HL-T1005A › Data sheetData Sheet
Sensors › Factory Automation Sensors › Laser Measurement Sensors › Ultra-compact Laser Collimated Beam Sensor HL-T1 › HL-T1005A › HL-T1HL-T1
Sensors › Factory Automation Sensors › Laser Measurement Sensors › Ultra-compact Laser Collimated Beam Sensor HL-T1 › HL-T1005A › HL-T1001□ / HL-T1005□HL-T1001□ / HL-T1005□
Sensors › Factory Automation Sensors › Laser Measurement Sensors › Ultra-compact Laser Collimated Beam Sensor HL-T1 › HL-T1005A › HL-T1001□ / HL-T1005□HL-T1001□ / HL-T1005□
Sensors › Factory Automation Sensors › Laser Measurement Sensors › Ultra-compact Laser Collimated Beam Sensor HL-T1 › HL-T1005A › HL-T1001□ / HL-T1005□HL-T1001□ / HL-T1005□
Sensors › Factory Automation Sensors › Laser Measurement Sensors › Ultra-compact Laser Collimated Beam Sensor HL-T1 › HL-T1005A › HL-T1005A (Emitter)HL-T1005A (Emitter)
Sensors › Factory Automation Sensors › Laser Measurement Sensors › Ultra-compact Laser Collimated Beam Sensor HL-T1 › HL-T1005A › HL-T1005A (Receiver)HL-T1005A (Receiver)