HL-T1005F
Specification
| Item | Performance characteristics |
|---|---|
| Type | Sensing width 5 mm 0.197 in type |
| CE Marking Directive Compliance | EMC Directive, RoHS Directive |
| Applicable Controller | HL-AC1, HL-AC1P |
| Sensing Range | ■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - - |
| Emission Indicator | Green LED (lights up during laser emission) |
| Interference Prevention Function | Two units of sensors can be mounted close together. (When the controller interference prevention function is used) |
| Pollution Degree | 3 (industrial environment) |
| Environmental Resistance: Ambient Temperature | 0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉ |
| Environmental Resistance: Ambient Humidity | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Environmental Resistance: Ambient Illuminance | Incandescent light: 10,000 liter x or less at the light-receiving face |
| Voltage Withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Insulation Resistance | 100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure |
| Environmental Resistance: Vibration Resistance | 10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each |
| Environmental Resistance: Shock Resistance | 300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each |
| Emitting Element: IEC/JIS Standards Conforming Type | Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) |
| Emitting Element: FDA Regulations Conforming Type | Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1) |
| Material | Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass |
| Cable | 0.09mm2 3-core shielded cable with connector, 0.5 m 1.640 ft long |
| Cable Extension | Extension up to total 10 m 32.808 ft is possible, with the optional cable. |
| Weight (Typ.) | Emitter: 15 g approx. Receiver: 15 g approx. |
| Accessory | MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set |
Stock Check
Important
The service is owned, operated, controlled and managed by Panasonic's distributors.
For pricing, delivery and technical questions related to this service, please direct to them.
Panasonic assumes no responsibility for any dealings you may have with distributors.
