Part Number List

Results 9
Models table for series Ultra-slim Body Picking Sensor NA1-PK5/NA1-5
Part No.DatasheetCE Marking Directive ComplianceSensing heightSensing rangeBeam PitchNumber of beam channelsSensing objectSupply voltagePower consumptionOutputOutput:Utilization categoryOutput:Output operationOutput:Short-circuit protectionResponse timeIndicators:EmitterIndicators:ReceiverInterference prevention functionPollution degreeProtectionAmbient TemperatureAmbient HumidityAmbient IlluminanceVoltage withstandabilityInsulation resistanceVibration resistanceShock resistanceEmitting ElementMaterialCableCable ExtensionWeight (Typ.)
EMC Directive, RoHS Directive
100 mm 3.937 in
0.2 to 3 m 0.656 to 9.843 ft (0.05 to 1 m 0.164 to 3.281 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.5 W or less
Receiver: 0.8 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1 V or less (at 100 mA sink current), 0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.2 to 3 m 0.656 to 9.843 ft (0.05 to 1 m 0.164 to 3.281 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.5 W or less
Receiver: 0.8 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1 V or less (at 100 mA sink current), 0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.2 to 3 m 0.656 to 9.843 ft (0.05 to 1 m 0.164 to 3.281 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.6 W or less
Receiver: 0.9 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1 V or less (at 100 mA source current), 0.4 V or less (at 16 mA source current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.1 to 1.2 m 0.328 to 3.937 ft (0.05 to 0.5 m 0.164 to 1.640 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.5 W or less
Receiver: 0.8 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1 V or less (at 100 mA sink current), 0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.1 to 1.2 m 0.328 to 3.937 ft (0.05 to 0.5 m 0.164 to 1.640 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.6 W or less
Receiver: 0.9 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1 V or less (at 100 mA source current), 0.4 V or less (at 16 mA source current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.2 to 3 m 0.656 to 9.843 ft
(0.05 to 1 m 0.164 to 3.281 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.6 W or less
Receiver: 0.9 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1 V or less (at 100 mA source current), 0.4 V or less (at 16 mA source current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
Net weight: Emitter 70 g approx., Receiver 80 g approx.
Gross weight: 270 g approx.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.2 to 3 m 0.656 to 9.843 ft
(0.05 to 1 m 0.164 to 3.281 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.5 W or less
Receiver: 0.8 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1 V or less (at 100 mA sink current), 0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
Net weight: Emitter 70 g approx., Receiver 80 g approx.
Gross weight: 270 g approx.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.1 to 1.2 m 0.328 to 3.937 ft
(0.05 to 0.5 m 0.164 to 1.640 ft when set to SHORT)
(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.6 W or less
Receiver: 0.9 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
PNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1 V or less (at 100 mA source current), 0.4 V or less (at 16 mA source current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is High, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
Net weight: Emitter 80 g approx., Receiver 85 g approx.
Gross weight: 270 g approx.
EMC Directive, RoHS Directive
100 mm 3.937 in
0.1 to 1.2 m 0.328 to 3.937 ft
(0.05 to 0.5 m 0.164 to 1.640 ft when set to SHORT)(Note) The sensing range is the possible setting distance between the emitter and the receiver.
25 mm 0.984 in
5 beam channels
ø35 mm ø1.378 in or more opaque object
(completely beam interrupted object)
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 0.5 W or less
Receiver: 0.8 W or less
(Note) Obtain the current consumption by the following equation.
Current consumption = Power consumption / Supply voltage
(e.g.) When the supply voltage is 12 V, the current consumption of the emitter is
0.5 W / 12 V ≈ 0.042 A = 42 mA
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1 V or less (at 100 mA sink current), 0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
ON or OFF when one or more beam channels are interrupted / ON or OFF when two or more beam channels are interrupted, selectable by operation mode switch
Incorporated
10 ms or less (when the interference prevention is used, in Light state: 30 ms or less, in Dark state: 13 ms or less)
Power indicator: Green LED (lights up when the power is ON)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Operation indicator: Red LED (lights up when one or more beam channels are interrupted, but lights up when two beam channels or more are interrupted in the double-beaminterruption mode)
Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
Job indicator: Orange LED (lights up or blinks when the job indicator input is Low, lighting pattern is selected by operation mode switch)
Incorporated
3 (Industrial environment)
IP62 (IEC)
-10 to +55 ℃ +14 to +131 ℉
(No dew condensation or icing allowed),
Storage: -20 to +70 ℃ -4 to +158 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
490 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED
(Peak emission wavelength: 950 nm 0.037 mil, synchronized scanning system)
Enclosure: Heat-resistant ABS
Lens cover: Acrylic
Indicator cover: Acrylic
0.3 mm2 4-core (emitter: 3-core) oil resistant cabtyre cable, 2 m 6.562 ft long
Extension up to total 100 m 328.084 ft is possible for both emitter and receiver with 0.3 mm2, or more, cable.
Net weight: Emitter 80 g approx., Receiver 85 g approx.
Gross weight: 270 g approx.