Part Number List

Results 37
Models table for series 40 mm Beam Pitch General Purpose Area Sensor NA40
Part No.DatasheetSensing heightSensing rangeBeam PitchSensing objectSupply voltageCurrent consumptionSensing outputSensing output:Output operationSensing output:Short-circuit protectionSelf-diagnosis outputSelf-diagnosis output:Output operationSelf-diagnosis output:Short-circuit protectionResponse timeIndicatorInterference prevention functionProtectionAmbient TemperatureAmbient HumidityAmbient IlluminanceVoltage withstandabilityInsulation resistanceVibration resistanceShock resistanceEmitting ElementMaterialCable ExtensionWeight(Total weight of emitter and receiver)AccessoriesCable
920 mm 36.221 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 35 mA or less
Receiver: 115 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
2,190 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
920 mm 36.221 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC ±10 % Ripple P-P 10 % or les
Emitter: 35 mA or less
Receiver: 115 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable.
(However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
520 mm 20.472 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC ±10 % Ripple P-P 10 % or less
Emitter: 35 mA or less
Receiver: 90 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable.
(However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
1,020 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
360 mm 14.173 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC ±10 % Ripple P-P 10 % or less
Emitter: 35 mA or less
Receiver: 90 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable.
(However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
770 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
520 mm 20.472 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 35 mA or less
Receiver: 90 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
1,330 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
520 mm 20.472 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC ±10 % Ripple P-P 10 % or les
Emitter: 35 mA or less
Receiver: 90 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable.
(However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
120 mm 4.724 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC ±10 % Ripple P-P 10 % or less
Emitter: 30 mA or less
Receiver: 60 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable.
(However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
400 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
360 mm 14.173 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 35 mA or less
Receiver: 90 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable
990 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
200 mm 7.874 in
5 m 16.404 ft
40 mm 1.575 in
ø60 mm ø2.362 in or more opaque object
12 to 24 V DC ±10 % Ripple P-P 10 % or les
Emitter: 30 mA or less
Receiver: 60 mA or less
NPN open-collector transistor
• Maximum sink current: 100 mA
• Applied voltage: 30 V DC or less (between sensing output and 0 V)
• Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V)
• Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated with the three color indicators on the receiver
• Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted)
• Stable incident beam indicator: Green LED (lights up when all beam channels are received stably)
• Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably)
* When the output transistor fails, the three color indicators blink simultaneously.
Incorporated (Two units of sensors can be mounted close together.)
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum
Unit case: ABS
Front cover: Acrylic
Lens: Acrylic
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable.
(However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver
Adjusting screwdriver: 1 pc.
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end
* Use together with the optional mating cable