Part Number List

Results 32
Models table for series Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100
Part No.DatasheetCE Marking Directive ComplianceType of pressureRated pressure rangePressure withstandabilityApplicable FluidSupply voltageCurrent consumptionAnalog Voltage OutputProtectionAmbient TemperatureAmbient HumidityVoltage withstandabilityInsulation resistanceVibration resistanceShock resistanceTemperature characteristicsPressure portMaterialConnecting methodCableCable ExtensionWeight : Net weightWeight : Gross weightAccessoriesRemarkApplicable Sensor HeadDisplay / set pressure rangePower consumptionSensor head supply voltageSensor head inputComparative OutputComparative Output: Output OperationComparative Output: HysteresisComparative Output: RepeatabilityComparative Output: Response TimeWeight (Typ.)
EMC Directive, RoHS Directive
Gauge pressure
0 to +1.000 MPa
1.5 MPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M5 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to +1.000 MPa
1.5 MPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M5 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M3 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
-100.0 to +100.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M5 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M5 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
-100.0 to +100.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Compound pressure : -100.0 to +100.0kPa
Vacuum pressure : 0 to -101kPa
12 to 24 V DC ±10 % Ripple P-P 10 % or less
-10 to +50℃ +14 to +122℉ (cascading 8 to 16 controllers : -10 to +45℃ +14 to +133℉)(No dew condensation or icing allowed), Storage : -20 to +70℃ -4 to +158℉
35 to 85 % RH, Storage : 35 to 85 % RH
Over ambient temperature range -10 to +50℃ +14 to +122℉ : within ±0.5 % F.S. of pressure at +25℃ +77℉
Enclosure : Heat-resistant ABS, Protective cover : Polycarbonate, Jog switch : ABS, MODE key : Acrylic
・Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.
・The cable for controller connection is not supplied as an accessory. Make sure to use the quick-connection cables (optional) given below.
Main cable (4-core) : CN-74-C1 (cable length : 1m 3.281 ft), CN-74-C2 (cable length : 2 m 6.562 ft), CN-74-C5 (cable length : 5 m 16.404 ft)
Sub cable (2-core) : CN-72-C1 (cable length : 1m 3.281 ft), CN-72-C2 (cable length : 2 m 6.562 ft), CN-72-C5 (cable length : 5 m 16.404 ft)
・The values specified above are applied only to the controller.
Compound pressure : DPH-101□
Vacuum pressure : DPH-103□
Compound pressure : -199.9 to +199.9 kPa
Vacuum pressure : +101.3 to -101.3 kPa
Normal operation : 650 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
ECO mode : 500 mW or less (Current consumption 20 mA or less at 24 V supply voltage)
(Note): Excluding current consumption of the applicable pressure sensor head.
Same as supply voltage
Input voltage range : 1 to 5 V DC (over rated pressure range)
NPN open-collector transistor
・Maximum sink current : 50 mA (Note 1)
・Applied voltage : 30 V DC or less (between comparative output and 0 V)
・Residual voltage : 1.5 V or less (Note 2) [at 50 mA (Note 1) sink current]
(Note 1): 25 mA max. if 5 or more controllers are connected together.
(Note 2): In case of using the quick-connection cable (cable length : 5 m 16.404 ft)(optional)
NO / NC, selectable by jog switch
Minimum 0 digit, variable by hysteresis setting
With compound pressure type connected : within ±0.2 % F.S. (±4 digits), With vacuum / positive pressure type connected : within ±0.2 % F.S. (±2 digits)
150 μs, 500 μs, 1 ms, 5 ms, 10 ms, 50 ms, 100 ms, 500 ms, selectable by jog switch
Net weight : 20 g approx.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M3 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.