LS-501P
Specification
| Item | Performance characteristics |
|---|---|
| CE Marking Directive Compliance | EMC Directive, RoHS Directive |
| Operation Indicator | Orange LED (lights up when sensing output 1 or sensing output 2 is ON) |
| Protection | IP40(IEC) |
| Ambient Temperature | -10 to +55degrees + 14 to 131 degrees Fahrenheit (If 4 to 7 units are mounted close together, -10 to +50 degrees +14 to +122 degrees Fahrenheit ; if 8 to 16 units are mounted close together, -10 to +45 degrees +14 to +113 degrees Fahrenheit )(No dew condensation or icing allowed), Storage: -20 to +70 degrees -4 to +158 degrees Fahrenheit |
| Ambient Humidity | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Voltage Withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Insulation Resistance | 20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure |
| Vibration Resistance | 10 to 150 Hz frequency, 0.75 mm 0.030 in (max. 10 G) amplitude in X, Y and Z directions for two hours each |
| Shock Resistance | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each |
| Material | Enclosure: Polycarbonate Cover: Polycarbonate Switch: Polyacetal |
| Cable | - |
| Weight (Typ.) | Net weight: 15 g approx. Gross weight: 55 g approx. |
| Accessory | FX-MB1 (Amplifier protective seal): 1 set |
| Supply Voltage | 12 to 24 V DC +10-15% Ripple P-P 10 % or less |
| Power Consumption | Normal operation: 1,200 mW or less (Current consumption 50 mA or less at 24 V supply voltage) ECO mode: 980 mW or less (Current consumption 40 mA or less at 24 V supply voltage) |
| Sensing Outputs (Sensing Output 1, 2) | PNP open-collector transistor ・Maximum source current: 50 mA (Note：25 mA if 5 or more amplifier are connected in cascade (excluding cable extension).) ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 2 V or less (at max. source current) (Note：Select either sensing output 2 or external input as the connector type.) |
| Sensing Outputs (Sensing Output 1, 2): Output Operation | Selectable either Light-ON or Dark-ON |
| Sensing Outputs (Sensing Output 1, 2): Short-Circuit Protection | Incorporated |
| Sensing Output Setting: Sensing Output 1 | Normal mode, differential mode, hysteresis mode, window comparator mode, selectable |
| Sensing Output Setting: Sensing Output 2 | Normal mode, differential mode, hysteresis mode, self-diagnostic output mode, selectable (Note：Select either sensing output 2 or external input.) |
| Response Time | H-SP: 60 micro s or less, FAST: 150 micro s or less, STD: 250 micro s or less, LONG: 500 micro s or less, U-LG: 5 ms or less, HYPR: 24 ms or less selectable |
| Monitor Current Output | - |
| External Input | PNP non-contact input - Signal condition High: +4 Vto+V DC(sink current 3.0 mA or less), Low: 0 to +0.6 V DC or open - Input impedance: 10 kOhm approx. (Note：Select either sensing output 2 or external input.) |
| External Input Function | Laser emission halt / teaching (full-auto teaching, limit teaching, 2 point teaching) / logic operation setting / copy lock /display adjustment / data bank load / data bank save, selectable |
| Laser Emission Indicator | Green LED (lights up during laser emission) |
| Output select Indicator | Yellow LED (lights up when output is selected) |
| Digital Display | 8-digit 7-segment digital display (4-digit green LED + 4-digit red LED), MODE indicator (Yellow LED): L/D, CUST, PRO |
| Incident Light Indication Range | H-SP/FAST/STD: 0 to 4,000 LONG/U-LG/HYPR: 0 to 9,999 |
| Sensitivity Setting | 2-level teaching / limit teaching / full auto teaching / manual adjustment |
| Logical Operation | Between sensing output 1 and calculation target: Disabled / and / or / xor, selectable Calculation target: Sensing output 2 / adjacent upstream amplifier (sensing output 1) / external input, selectable |
| Timer Function | OFF-delay timer, ON-delay timer, ONE-SHOT timer, ON / OFF-delay timer, ON-delay / ONE-SHOT timer, switchable either effective of ineffective, with variable timer period OFF-delay timer, ON-delay timer, ONE-SHOT timer, switchable either effective of ineffective, with variable timer period |
| Timer Function: Time | Timer range '' ms'': 0.5 ms approx., 1 to 9,999 ms approx., in approx. 1 ms intervals Timer range '' sec'': 0.5 sec. approx., 1 to 32 sec. approx., in approx. 1 sec. intervals Timer range '' 1/10 ms'': 0.05 ms approx., 0.1 to 999.9 ms approx., in approx. 0.1 ms intervals, Set separately for each output. |
| Automatic Interference Prevention Function | Incorporated (Note：Number of units that can be mounted close together: 0 for H-SP; 2 for FAST; 4 for STD, LONG, U-LG, or HYPR) |
| Cable Extension | Extension up to total 100 m 328.084 ft is possible with 0.3mm2, or more, cable. |
Stock Check
Important
The service is owned, operated, controlled and managed by Panasonic's distributors.
For pricing, delivery and technical questions related to this service, please direct to them.
Panasonic assumes no responsibility for any dealings you may have with distributors.
