Part Number List

Results 1
Models table for series Thin-type Ionizer ER-VW
Part No.DatasheetCE Marking Compliant DirectivesCharge Removal TimeIon balanceOzone generationApplicable FluidSupplied air flowAir Pressure RangeSupply voltageCurrent consumptionDischarge methodDischarge output voltageOutput [Check (CHECK) Error (ERROR) Discharge (DSC)]Output:Output operationOutput:Short-circuit protectionDischarge halt input (DSC OFF)Reset input (RESET)Indicators:Power (POWER)Indicators:Discharge (DSC)Indicators:Air monitoring (AIR)Indicators:Check (CHECK)Indicators:Error (ERROR)Ambient TemperatureAmbient HumidityI/O connectorConnectable UnitsEnclosure earthingMaterialWeight (Typ.)Accessories
EMC Directive, RoHS Directive
1 sec. or less (plus or minus1,000 V to plus or minus100 V)
(Note) A typical sample applied with a supply voltage of 24 V, a distance of 100 mm 3.937 in from the front surface of the air flow outlet and a pressure of 0.25 MPa. (Measured on a sample left in the atmosphere at a relative humidity of 65 % RH or less for 24 hours or more.)
plus or minus10 V or less
(Note) A typical sample applied with a supply voltage of 24 V, a distance of 100 mm 3.937 in from the front surface of the air flow outlet and a pressure of 0.25 MPa. (Measured on a sample left in the atmosphere at a relative humidity of 65 % RH or less for 24 hours or more.)
0.05 ppm or less
(Note) A typical sample applied with a supply voltage of 24 V, a distance of 300 mm 11.811 in from the front surface of the air flow outlet and a pressure of 0.25 MPa.
Air (dried clean air)
(Note) Dry clean air is air that has been processed through an air dryer (freezing point around –20 ℃ –4 ℉) and an air filter (mesh size around 0.01 microm 0.0004 mil).
60 liter/min. (ANR) or less
0.05 to 0.5 MPa
24 V DC plus or minus 10 %
120 mA or less
High frequency AC method
2,000 V approx.
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 1 V or less (at 50 mA sink current)
(Note:"DSC" is an abbreviated name of "DISCHARGE".)
Check output (CHECK): ON when the discharge needle is dirty or worn, OFF when operation is normal
Error output (ERROR): OFF when abnormal discharge is detected, ON when operation is normal
Discharge output (DSC) (Note): ON when discharging, OFF when discharge halts
(Note) ‘‘DSC’’ is an abbreviated name of ‘‘DISCHARGE’’.
Incorporated
Short-circuit to 0 V: Discharge halt, Open: Discharge allowed (operation start)
(Note:"DSC" is an abbreviated name of "DISCHARGE".)
In the state that operation is stopped due to an error detection, open 0 V of the power supply from short-circuit state to cancel ERROR
Green LED (lights up when the power is ON)
Green LED (lights up when discharging)
(Note) ‘‘DSC’’ is an abbreviated name of ‘‘DISCHARGE’’.
Orange LED (lights up when no air is being supplied)
(Note) Discharge halts when lights up.
Orange LED (lights up when the discharge needle is dirty or worn, etc.)
Red LED (lights up when abnormal discharge is detected)
0 to +55 ℃ +32 to +131 ℉ (No dew condensation allowed), Storage: –10 to +65 ℃ +14 to +149 ℉
35 to 65 % RH (No dew condensation allowed), Storage: 35 to 65 % RH
For power & input / output: 8-pin connector, For connection: 9-pin connector
Maximum number of connectable units: 5 (Including this unit)
Capacitor earth
Enclosure: ABS (Nickel plated), Nozzle mount, Screw mount, Nozzle: Stainless steel. Discharge needle: Tungsten
Net weight: 110 g approx., Gross weight: 180 g approx.
Connector attached cable: 1 pc. (length 0.5 m 1.640 ft), End connector (9-pin): 1 pc., Lead wire for connecting F.G.: 1 pc.