Part Number List

Results 30
Models table for series FP0R
Part No.Datasheetgramming method / Control methodNumber of I/O points : No expansion (Control unit only)Number of I/O points : With expansion 1
Same type of control and expansion units
Number of I/O points : With expansion 2
Mix type of relay and transistor units
gram memorygram capacityNumber of instructions : BasicNumber of instructions : High-levelOperation speed : Up to 3,000 stepsOperation speed : 3,001st and later stepsOperation memory : Relay : Internal relay (R)Operation memory : Relay : Timer / Counter (T / C)Operation memory : Memory area : Data register (DT)Operation memory : Memory area : Index register (IX, IY)Master control relay points (MCR)Number of labels (JMP and LOOP)Differential pointsNumber of step ladderNumber of subroutinesSpecial functions : High speed counterSpecial functions : Pulse outputSpecial functions : PWM outputSpecial functions : Pulse catch input / interrupt inputSpecial functions : Interrupt programSpecial functions : Periodical interruptSpecial functions : Constant scanSpecial functions : RS485 portMaintenance : Memory backup : Program and system registerMaintenance : Memory backup : Operation memoryMaintenance : Self-diagnostic functionMaintenance : Real-time clock functionMaintenance : Other functionsRated voltageOperating voltage rangeAllowed Momentary Power Off TimeOperating TemperatureStorage temperatureOperating humidityStorage humidityBreakdown Voltage (Detection Current: 5 mA)Insulation resistance (Test voltage: 500 V DC)Vibration resistanceShock resistanceNoise immunityOperating environmentRated input voltageApplied Voltage RangeRated input currentmpedancer commonMin. ON voltage/Min. ON currentResponse time : OFF→ONResponse time : ON→OFFlation methodRemarkypeRated load voltageLoad voltage allowable rangeMax. switching currentFF state leakage currentN state voltage dropExternal power : VoltageExternal power supply : CurrentSurge absorberInsulation methodRated control capacityLife time : MechanicalLife time : ElectricalSpecial functions : RS-232C port
Relay symbol / Cyclic operation
32 points
[Input : 16, Transistor output : 16]
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
32 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
32,765 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
4 points (50 kHz max. each) 2 channels can be controlled individually. (Note: For the limitations while operating units, reter to the manual.)
4 points (6 Hz to 4.8 kHz)
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
One RS485 port is mounted (3P terminal block)
Transmission speed (Baud rate) : 115.2 kbps (It is possible to change to 19.2 kbps by the setting.), Transmission distance : 1,200 m 3,937 ft, Communication method : half duplex
Stored program and system register in EEPROM
Backup of the entire area by FeRAM
(without the need for a battery)
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
10 ms (20.4 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
16 points / common
19.2 V / 2 mA
20 μs or less (Load current : 5 mA or more), 0.1 ms or less (Load current : 0.5 mA or more)
40 μs or less (Load current : 5 mA or more), 0.2 ms or less (Load current : 0.5 mA or more)
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
Open collector
5 to 24 V DC
4.75 to 26.4 V DC
0.2 A / point (Max. 14 per common terminal)
1 μA or less
0.2 V DC or less
21.6 to 26.4 V DC
60 mA or less
Zener diode
Photocoupler
Relay symbol / Cyclic operation
10 points
[Input : 6,
Relay output : 4]
Max. 58 points (Note: For the limitations while operating units, reter to the manual.)
Max. 106 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
16 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
12,315 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
Not available
Not available
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
One RS485 port is mounted (3P terminal block)
Transmission speed (Baud rate) : 115.2 kbps (It is possible to change to 19.2 kbps by the setting.), Transmission distance : 1,200 m 3,937 ft, Communication method : half duplex
Stored program and system register in EEPROM
Stored fixed area in EEPROM
Counter : 16 points
Internal relay : 128 points
Data register : 315 words
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
5 ms (at 20.4 V DC), 10 ms (21.6 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
2 points / common + 1 point / common + 1point / comon
19.2 V / 2 mA
10 ms approx.
8 ms approx.
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
1a
None
2 A 250 V AC, 2 A 30 V DC (4.5 A / common)
2 x 107 operations or more
105 operations or more
Relay symbol / Cyclic operation
32 points
[Input : 16, Transistor output : 16]
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
32 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
32,765 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
4 points (50 kHz max. each) 2 channels can be controlled individually. (Note: For the limitations while operating units, reter to the manual.)
4 points (6 Hz to 4.8 kHz)
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
Stored program and system register in EEPROM
Backup of the entire area by FeRAM
(without the need for a battery)
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
10 ms (20.4 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
16 points / common
19.2 V / 2 mA
20 μs or less (Load current : 5 mA or more), 0.1 ms or less (Load current : 0.5 mA or more)
40 μs or less (Load current : 5 mA or more), 0.2 ms or less (Load current : 0.5 mA or more)
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
Open collector
5 to 24 V DC
4.75 to 26.4 V DC
0.2 A / point (Max. 14 per common terminal)
1 μA or less
0.2 V DC or less
21.6 to 26.4 V DC
60 mA or less
Zener diode
Photocoupler
One RS-232C port is mounted
(3P terminal block) Transmission speed (Baud rate) : 2,400 to 115,200 bits/s, Transmission distance : 15 m 9.843 ft. Communication method : half duplex
Relay symbol / Cyclic operation
14 points
[Input : 8,
Relay output : 6]
Max. 62 points (Note: For the limitations while operating units, reter to the manual.)
Max. 110 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
16 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
12,315 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
Not available
Not available
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
Stored program and system register in EEPROM
Stored fixed area in EEPROM
Counter : 16 points
Internal relay : 128 points
Data register : 315 words
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
5 ms (at 20.4 V DC), 10 ms (21.6 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
4 points / common + 1 point / common + 1point / comon
19.2 V / 2 mA
10 ms approx.
8 ms approx.
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
1a
None
2 A 250 V AC, 2 A 30 V DC (4.5 A / common)
2 x 107 operations or more
105 operations or more
Relay symbol / Cyclic operation
16 points
[Input : 8,
Transistor output : 8]
Max. 112 points (Note: For the limitations while operating units, reter to the manual.)
Max. 112 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
16 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
12,315 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
4 points (50 kHz max. each) 2 channels can be controlled individually. (Note: For the limitations while operating units, reter to the manual.)
4 points (6 Hz to 4.8 kHz)
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
Stored program and system register in EEPROM
Stored fixed area in EEPROM
Counter : 16 points
Internal relay : 128 points
Data register : 315 words
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
5 ms (at 20.4 V DC), 10 ms (21.6 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
8 points / common
19.2 V / 2 mA
20 μs or less (Load current : 5 mA or more), 0.1 ms or less (Load current : 0.5 mA or more)
40 μs or less (Load current : 5 mA or more), 0.2 ms or less (Load current : 0.5 mA or more)
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
Open collector
24 V DC
21.6 to 26.4 V DC
0.2 A / point (Max. 14 per common terminal)
1 μA or less
0.2 V DC or less
21.6 to 26.4 V DC
35 mA or less
Zener diode
Photocoupler
Relay symbol / Cyclic operation
32 points
[Input : 16, Transistor output : 16]
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
32 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
32,765 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
4 points (50 kHz max. each) 2 channels can be controlled individually. (Note: For the limitations while operating units, reter to the manual.)
4 points (6 Hz to 4.8 kHz)
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
One RS485 port is mounted (3P terminal block)
Transmission speed (Baud rate) : 115.2 kbps (It is possible to change to 19.2 kbps by the setting.), Transmission distance : 1,200 m 3,937 ft, Communication method : half duplex
Stored program and system register in EEPROM
Stored fixed area in EEPROM
Counter : 16 points
Internal relay : 128 points
Data register : 315 words
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
10 ms (20.4 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
16 points / common
19.2 V / 2 mA
20 μs or less (Load current : 5 mA or more), 0.1 ms or less (Load current : 0.5 mA or more)
40 μs or less (Load current : 5 mA or more), 0.2 ms or less (Load current : 0.5 mA or more)
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
Open collector
24 V DC
21.6 to 26.4 V DC
0.2 A / point (Max. 14 per common terminal)
1 μA or less
0.2 V DC or less
21.6 to 26.4 V DC
70 mA or less
Zener diode
Photocoupler
Relay symbol / Cyclic operation
32 points
[Input : 16, Transistor output : 16]
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
32 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
32,765 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
4 points (50 kHz max. each) 2 channels can be controlled individually. (Note: For the limitations while operating units, reter to the manual.)
4 points (6 Hz to 4.8 kHz)
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
Stored program and system register in EEPROM
Backup of the entire area by FeRAM
(without the need for a battery)
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
10 ms (20.4 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
16 points / common
19.2 V / 2 mA
20 μs or less (Load current : 5 mA or more), 0.1 ms or less (Load current : 0.5 mA or more)
40 μs or less (Load current : 5 mA or more), 0.2 ms or less (Load current : 0.5 mA or more)
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
Open collector
24 V DC
21.6 to 26.4 V DC
0.2 A / point (Max. 14 per common terminal)
1 μA or less
0.2 V DC or less
21.6 to 26.4 V DC
70 mA or less
Zener diode
Photocoupler
One RS-232C port is mounted
(3P terminal block) Transmission speed (Baud rate) : 2,400 to 115,200 bits/s, Transmission distance : 15 m 9.843 ft. Communication method : half duplex
Relay symbol / Cyclic operation
10 points
[Input : 6,
Relay output : 4]
Max. 58 points (Note: For the limitations while operating units, reter to the manual.)
Max. 106 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
16 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
12,315 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
Not available
Not available
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
Stored program and system register in EEPROM
Stored fixed area in EEPROM
Counter : 16 points
Internal relay : 128 points
Data register : 315 words
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
5 ms (at 20.4 V DC), 10 ms (21.6 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
2 points / common + 1 point / common + 1point / comon
19.2 V / 2 mA
10 ms approx.
8 ms approx.
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
1a
None
2 A 250 V AC, 2 A 30 V DC (4.5 A / common)
2 x 107 operations or more
105 operations or more
Relay symbol / Cyclic operation
14 points
[Input : 8,
Relay output : 6]
Max. 62 points (Note: For the limitations while operating units, reter to the manual.)
Max. 110 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
16 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
12,315 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
Not available
Not available
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
Stored program and system register in EEPROM
Stored fixed area in EEPROM
Counter : 16 points
Internal relay : 128 points
Data register : 315 words
Watchdog timer (690 ms approx.), Program syntax check
Not available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
5 ms (at 20.4 V DC), 10 ms (21.6 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
4 points / common + 1 point / common + 1point / comon
19.2 V / 2 mA
10 ms approx.
8 ms approx.
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
1a
None
2 A 250 V AC, 2 A 30 V DC (4.5 A / common)
2 x 107 operations or more
105 operations or more
One RS-232C port is mounted
(3P terminal block) Transmission speed (Baud rate) : 2,400 to 115,200 bits/s, Transmission distance : 15 m 9.843 ft. Communication method : half duplex
Relay symbol / Cyclic operation
32 points
[Input : 16, Transistor output : 16]
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
Max. 128 points (Note: For the limitations while operating units, reter to the manual.)
EEPROM (no backup battery required)
32 k steps
110 approx.
210 approx.
Basic instructions : 0.08 μs min. Timer instructions : 2.2 μs min.
High-level instructions : 0.32 μs (MV instruction) min.
Basic instructions : 0.58 μs min. Timer instructions : 3.66 μs min.
High-level instructions : 1.62 μs (MV instruction) min.
4,096 points
1,024 points
32,765 words
14 words (IO to ID)
256 words
256 labels
Equivalent to the program capacity
1,000 stages
500 subroutines
Single-phase: 6 points (50 kHz max. each) 2-phase: 3 channels (15 kHz max. each) (Note: For the limitations while operating units, reter to the manual.)
4 points (50 kHz max. each) 2 channels can be controlled individually. (Note: For the limitations while operating units, reter to the manual.)
4 points (6 Hz to 4.8 kHz)
Total 8 points (with high speed counter)
Input : 8 programs (6 programs for C10 only)
/ Periodic : 1 program / Pulse match : 4 programs/td>
In units of 0.5 ms : 0.5 ms to 1.5 sec. / In units of 10 ms : 10 ms to 30 sec.
In units of 0.5 ms : 0.5 ms to 600 ms
One RS485 port is mounted (3P terminal block)
Transmission speed (Baud rate) : 115.2 kbps (It is possible to change to 19.2 kbps by the setting.), Transmission distance : 1,200 m 3,937 ft, Communication method : half duplex
Stored program and system register in EEPROM
Backup of the entire area by a built-in secondary battery
Watchdog timer (690 ms approx.), Program syntax check
Available
Rewriting in RUN mode, Download in RUN mode (incl. comments),
8-character password setting, and Program upload protection
24 V DC
20.4 to 28.8 V DC
10 ms (20.4 V DC or higher)
0 to +55 ℃ 32 to +131 ℉
-40 to +70 ℃ -40 to +158 ℉ (-20 ℃ to +70 ℃ -4 to +158 ℉ for T32 only)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
10 to 95% RH (at 25 ℃ 77 ℉, no condensation)
Input terminals - output terminals, Output terminals - power and functional ground terminals --- Transistor output : 500 V AC for 1 minute (Relay output : 1,500 V AC for 1 minute) /
Input terminals - power and functional ground terminals, Functional ground terminal - power terminal --- Transistor output : 500 V AC for 1 minute (Relay output : 500 V AC for 1 minute) /
Output terminals - output terminals (different common terminals) --- Relay output : 1,500 V AC for 1 minute
Input terminals - output terminals, input terminals - power and functional ground terminals, output terminals - power and functional ground terminals, functional ground terminal - power terminal --- Transistor output : 100 MΩ minimum (relay output : 100 MΩ minimum) /
Output terminals - output terminals (different common terminals) --- Relay output : 100 MΩ minimum
5 to 9 Hz, single amplitude of 3.5 mm, 1 sweep/min; 9 to 150 Hz, constant acceleration of 9.8 m/s2, 1 sweep/min; for 10 min each in X, Y, and Z directions
147 m/s2 or more , 4 times each in X, Y, and Z directions
1,000 V (p-p) with pulse widths 50 ns and 1 μs (using a noise simulator)(Power supply terminal)
Free from corrosive gasses and excessive dust
24 V DC
21.6 to 26.4 V DC
2.6 mA approx. (at 24 V DC)
9.1 kΩ approx.
16 points / common
19.2 V / 2 mA
20 μs or less (Load current : 5 mA or more), 0.1 ms or less (Load current : 0.5 mA or more)
40 μs or less (Load current : 5 mA or more), 0.2 ms or less (Load current : 0.5 mA or more)
Photocoupler
Since the response time of X0 to X7 is very fast (for high-speed counter input) the FP0 happens to chattering noise as an input signal. To prevent this, it is recommended that the timer should be put in the ladder program.
Open collector
24 V DC
21.6 to 26.4 V DC
0.2 A / point (Max. 14 per common terminal)
1 μA or less
0.2 V DC or less
21.6 to 26.4 V DC
70 mA or less
Zener diode
Photocoupler

What's New

Stay up to date