Specifications
Item | Performance characteristics |
---|---|
CE Marking Directive Compliance | EMC Directive, RoHS Directive |
Supply Voltage | 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less |
Power Consumption | Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) |
Output | NPN open-collector transistor - Maximum sink current: 100 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 100 mA sink current) |
Output: Output Operation | Selectable either Light-ON or Dark-ON, at SET mode |
Output: Short-Circuit Protection | Incorporated |
External Input | NPN non-contact input - Signal condition High: +8 V to +V DC or Open Low: 0 to +2 V DC(Source current 0.5 mA or less) - Input impedance: 10 kOhm approx. |
Response Time | Emission frequency 1: 2.5 ms or less (factory default setting) Emission frequency 2: 2.8 ms or less Emission frequency 3: 3.2 ms or less Emission frequency 4: 5.0 ms or less |
Sensitivity Setting | 2-point teaching / Limit teaching / Full-auto teaching |
Operation Indicator | Orange LED (lights up when the output is ON) |
Digital Display | 4 digits (green) + 4 digits (red) LCD display |
Fine Sensitivity Adjustment Function | Incorporated |
Timer Function | ON-delay / OFF-delay timer, switchable either effective or ineffective [Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms] |
Emission Amount Setting Function | 3-level + Auto setting (from production in December 2007) |
Interference Prevention Function | Incorporated Emission frequency selection method (Functions at emission frequency 1, 2, 3 or 4) (Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values. |
Ambient Temperature | –10 to +55 ℃ +14 to +131 ℉ (If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 ℉, if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ℉) (No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ |
Ambient Humidity | 35 to 85 % RH, Storage: 35 to 85 % RH |
Ambient Illuminance | Incandescent light: 3,000 lx or less at the light-receiving face |
Voltage Withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only. |
Insulation Resistance | 20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only. |
Vibration Resistance | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each |
Shock Resistance | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each |
Emitting Element (Modulated) | Red LED (Peak emission wavelength: 643 nm 0.025 mil) |
Material | Enclosure: Polycarbonate Key switch: Polycarbonate Fiber lock lever: PBT |
Connecting Method | Connector (Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S). |
Cable Length | Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. |
Weight (Typ.) | Net weight: 15 g approx. Gross weight: 35 g approx. |
Accessory | FC-FX-1(Protection cover): 1 pc. (Note) Protection cover FC-FX-1 has been attached from the production at July, 2011. |