| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode: 840 mW or less (Current consumption 35 mA or less at 24 V supply voltage) | NPN open-collector transistor • Maximum sink current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and 0 V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Red LED | 650 nm 0.026 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 580 mW or less (Current consumption 24 mA or less at 24 V supply voltage) | NPN open-collector transistor • Maximum sink current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and 0 V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Blue LED | 470 nm 0.019 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 580 mW or less (Current consumption 24 mA or less at 24 V supply voltage) | NPN open-collector transistor • Maximum sink current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and 0 V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Green LED | 525 nm 0.021 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 580 mW or less (Current consumption 24 mA or less at 24 V supply voltage) | PNP open-collector transistor • Maximum source current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Blue LED | 470 nm 0.019 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode: 840 mW or less (Current consumption 35 mA or less at 24 V supply voltage) | NPN open-collector transistor • Maximum sink current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and 0 V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Red LED | 650 nm 0.026 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 580 mW or less (Current consumption 24 mA or less at 24 V supply voltage) | NPN open-collector transistor • Maximum sink current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and 0 V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Blue LED | 470 nm 0.019 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 580 mW or less (Current consumption 24 mA or less at 24 V supply voltage) | PNP open-collector transistor • Maximum source current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Green LED | 525 nm 0.021 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode: 840 mW or less (Current consumption 35 mA or less at 24 V supply voltage) | PNP open-collector transistor • Maximum source current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Red LED | 650 nm 0.026 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |
| | EMC Directive, RoHS Directive | 12 to 24 V DC ±10 % Ripple P-P 10 % or less | Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 580 mW or less (Current consumption 24 mA or less at 24 V supply voltage) | NPN open-collector transistor • Maximum sink current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) • Applied voltage: 30 V DC or less (between output and 0 V) • Residual voltage: 1.5 V or less [at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade)]
| Switchable either Light-ON or Dark-ON | Incorporated | 150 μs or less (FAST), 500 μs or less (STD), 4.5 ms or less (U-LG) selectable with setting switch | Orange LED (lights up when the output is ON) | Green LED (lights up under stable light received condition or stable dark condition) | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period (Note): 1 ms to 3 sec. approx. (1 to 10 ms: Setting possible in units of 1 ms, 10 to 100 ms: Setting possible in units of 10 ms, 100 to 500 ms: Setting possible in units of 50 ms, 500 ms to 1 sec.: Setting possible in units of 100 ms, 1 to 3 sec.: Setting possible in units of 500 ms)] (Note):For models manufactured up until June 2005, the timer period is approx. 1 to 500 ms. | Incorporated (Up to four sets of fiber heads can be mounted close together. However, U-LG mode is 8 fiber heads.) (Note:When the power supply is switched on, the light emission timing is automatically set for interference prevention.) | –10 to +55 ℃ –14 to +131 ℉
(If 4 to 7 units are connected in cascade: –10 to +50 ℃ +14 to +122 ℉,
if 8 to 16 units are connected in cascade: –10 to +45 ℃ +14 to +113 ℉)
(No dew condensation or icing allowed), Storage: –20 to +70 ℃ –4 to +158 ℉ | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 ℓx or less at the light-receiving face | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note:The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.) | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each | Green LED | 525 nm 0.021 mil | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | Net weight: 20 g approx., Gross weight: 30 g approx. |