Panasonic cube-shaped GXL Micro-Size Inductive Proximity Sensors are extremely small. Each Sensor is available in four different versions: front or side sensing with normally open or normally closed contacts and offering two detection frequencies to prevent mutual interference.
Characteristics
Extremely Small Design
Case / Cable Oil Resistant
Protection Class IP67
PNP/ NPN or non-contact 2-wire
Available With Different Frequencies (To Avoid Mutual Interference)
Interference Resistant Cable Available
Micro-size Inductive Proximity Sensor GXL
Part number list
Results 96
Models table for series Micro-size Inductive Proximity Sensor GXL
Part No.
Datasheet
CE Marking Directive Compliance
Max. Operation Distance
Stable Sensing Range
Standard Sensing Object
Hysteresis
Repeatability
Supply Voltage
Current Consumption
Output
Output: Utilization Category
Output: Short-Circuit Protection
Max. Response Frequency
Operation Indicator
Environmental Resistance: Pollution Degree
2-Color Indicator
Protection
Ambient Temperature
Ambient Humidity
Voltage Withstandability
Insulation Resistance
Vibration Resistance
Shock Resistance
Sensing Range Variation: Temperature Characteristics
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
Red LED(lights up when the output is ON)
3 (Industrial environment)
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
Red LED(lights up when the output is ON)
3 (Industrial environment)
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
Enclosure: PBT Indicator part: Polyarylate
0.2 mm2 2-core oil, heat and cold resistant cable, 1 m 3.281 ft long (Note:The bending-resistant cable type (model No. with suffix “-R”) has a 0.15 mm2 (GXL-15 type: 0.2 mm2) bending, oil, heat and cold resistant cabtyre cable, 1 m 3.281 ft long.)
Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
Red LED(lights up when the output is ON)
3 (Industrial environment)
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
5 mm 0.197 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 4 mm 0 to 0.157 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 20 × 20 × t 1 mm 0.787 × 0.787 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
Enclosure: PBT Indicator part: Polyarylate
0.2 mm2 2-core oil, heat and cold resistant cable, 1 m 3.281 ft long (Note:The bending-resistant cable type (model No. with suffix “-R”) has a 0.15 mm2 (GXL-15 type: 0.2 mm2) bending, oil, heat and cold resistant cabtyre cable, 1 m 3.281 ft long.)
Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.
5 mm 0.197 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 4 mm 0 to 0.157 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 20 × 20 × t 1 mm 0.787 × 0.787 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
5 mm 0.197 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 4 mm 0 to 0.157 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 20 × 20 × t 1 mm 0.787 × 0.787 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
Enclosure: PBT Indicator part: Polyarylate
Net weight: 20 g approx.
-
Models table for series Micro-size Inductive Proximity Sensor GXL
Part No.
Datasheet
CE Marking Directive Compliance
Max. Operation Distance
Stable Sensing Range
Standard Sensing Object
Hysteresis
Repeatability
Supply Voltage
Current Consumption
Output
Output: Utilization Category
Output: Short-Circuit Protection
Max. Response Frequency
Operation Indicator
Environmental Resistance: Pollution Degree
2-Color Indicator
Protection
Ambient Temperature
Ambient Humidity
Voltage Withstandability
Insulation Resistance
Vibration Resistance
Shock Resistance
Sensing Range Variation: Temperature Characteristics
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
Red LED(lights up when the output is ON)
3 (Industrial environment)
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
Red LED(lights up when the output is ON)
3 (Industrial environment)
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
Enclosure: PBT Indicator part: Polyarylate
0.2 mm2 2-core oil, heat and cold resistant cable, 1 m 3.281 ft long (Note:The bending-resistant cable type (model No. with suffix “-R”) has a 0.15 mm2 (GXL-15 type: 0.2 mm2) bending, oil, heat and cold resistant cabtyre cable, 1 m 3.281 ft long.)
Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
8 mm 0.315 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 6.4 mm 0 to 0.252 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 30 × 30 × t 1 mm 1.181 × 1.181 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
Red LED(lights up when the output is ON)
3 (Industrial environment)
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
5 mm 0.197 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 4 mm 0 to 0.157 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 20 × 20 × t 1 mm 0.787 × 0.787 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
Enclosure: PBT Indicator part: Polyarylate
0.2 mm2 2-core oil, heat and cold resistant cable, 1 m 3.281 ft long (Note:The bending-resistant cable type (model No. with suffix “-R”) has a 0.15 mm2 (GXL-15 type: 0.2 mm2) bending, oil, heat and cold resistant cabtyre cable, 1 m 3.281 ft long.)
Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.
5 mm 0.197 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 4 mm 0 to 0.157 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 20 × 20 × t 1 mm 0.787 × 0.787 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage
5 mm 0.197 in plus or minus 10% (Note) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
0 to 4 mm 0 to 0.157 in (Note) The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient temperature drift and/or supply voltage fluctuation.
Iron sheet 20 × 20 × t 1 mm 0.787 × 0.787 × t 0.039 in
20 % or less of operation distance(with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
0.8 mA or less (Note) It is the leakage current when the output is in the OFF state.
Non-contact DC 2-wire type - Load current: 3 to 100 mA (Note 1) - Residual voltage: 3 V or less (Note 2) (Note 1) The maximum load current varies with the ambient temperature. (Note 2) When the cable is extended, the residual voltage becomes larger according to the resistance of the cable. The residual voltage of 5 m 16.404 ft cable length type increases by +0.1 V.
DC-12 or DC-13
Incorporated
1 kHz
3 (Industrial environment)
Lights up in green under stable sensing condition Lights up in red under unstable sensing condition
IP67 (IEC), IP67 g (JEM) (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
-25 to +70 ℃ -13 to +158 ℉ , Storage: -30 to +80 ℃ -22 to +176 ℉
45 to 85 % RH, Storage: 35 to 95 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each
Over ambient temperature range -25 to +70 ℃ -13 to +158 ℉ : Within+15-10 % of sensing range at +20 ℃ +68 ℉
Within plus or minus 2 % for plus or minus 10 % fluctuation of the supply voltage