The Panasonic PM-65 Sensor has a beam emitting / receiving distance of 6 mm. The beam emitting and receiving areas are 0.5 mm thinner compared to conventional models even though the external dimensions have not changed. As a result, the distance between the beam-emitting and the beam-receiving points have increased by 1 mm thereby reducing the possibility of sensing objects colliding.
There are marks on the front and back of the Sensor to indicate the upper and lower limit of the beam axis. This makes it easy to adjust the position of the sensing object. Also, a large indicator light (orange) illuminates when an object enters the beam axis and can be visible from any angle above or from the sides.
Stress points in the PM-65 Sensor, such as where the cable and internal circuit meets, are re-enforced with resin to prevent malfunctions cause by vibrations or impacts. All models are designed with the following protection circuits in their compact shapes. These protection circuits minimize the possibility of Sensor malfunctions or damage caused by incorrect wiring.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
・Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. ・Mounting-compatible with our conventional models [PM-F54]
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
・Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. ・Mounting-compatible with our conventional models [PM-R54P]
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
・Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
Models table for series Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Compact / Connector built-in type] PM-65
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
・Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. ・Mounting-compatible with our conventional models [PM-F54]
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
・Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. ・Mounting-compatible with our conventional models [PM-R54P]
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
・Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and + V) ・Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
Incorporated with 2 outputs: Light-ON / Dark-ON
Incorporated
Under light received condition: 20 μs or less Under light interrupted condition: 80 μs or less (Maximum response frequency: 3 kHz)(Note) (Note) The response frequency is the value when the disc, given in the figure below, is rotated.
Orange LED (lights up under light received condition)
3
IP40 (IEC)
-25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +80 ℃ -22 to +176 ℉
5 to 85 % RH, Storage: 5 to 95 % RH
Fluorescent light: 1,000 ℓx at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each
15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated)
Enclosure: PBT Display section: Polycarbonate
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher.
Net weight: 3 g approx. Gross weight: 3 g approx.
Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
