Ultra-compact Photoelectric Sensor EX-20 Ver.2

Using a single chip optical IC, Panasonic created the powerful EX-20 Ultra-Compact Photoelectric Sensors, which are among the smallest Photoelectric Sensors worldwide and in spite of their miniature size, the Sensors incorporate a sensitivity adjuster. Since a red LED dot light source is used, alignment and confirmation of the sensing position is easy, even if very tiny objects have to be detected.

Characteristics:

Miniature Construction
Response Time Only 0.5ms
Red LED
New: Up To 35% Less Power Consumption
New: Improved Ambient Light Immunity
Adjustable Sensitivity
Thru-Beam
Diffuse Reflective
Sealed To IP67
2 Indicator LEDs

Models table for series Ultra-compact Photoelectric Sensor EX-20 Ver.2
Part No.	CE Marking Directive Compliance	Sensing Range	Sensing Object	Hysteresis	Repeatability (Perpendicular to Sensing Axis)	Supply Voltage	Current Consumption	Output	Output: Utilization Category	Output: Short-Circuit Protection	Response Time	Operation Indicator	Stability Indicator	Protection	Operation Mode Switch	Sensitivity Adjuster	Ambient Temperature	Ambient Humidity	Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Emitting Element	Emitting Element: Peak Emission Wavelength	Material	Cable	Cable Extension	Weight (Typ.)	Accessory
EX-29B-PN-Y	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc
EX-29B-Y	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc
EX-29B-Y-C5	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.		Adjusting screwdriver: 1 pc
EX-29A-Y-C5	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.		Adjusting screwdriver: 1 pc
EX-28B	EMC Directive, RoHS Directive	45 to 115 mm 1.772 to 4.528 in with white non-glossy paper (100 x 100 mm 3.937 x 3.937 in), spot diameter dia. 5 mm dia. 0.197 in with setting distance 80 mm 3.150 in	Opaque, translucent or transparent object (Note) (Min. dia. 1 mm dia. 0.039 in copper wire at setting distance 80 mm 3.150 in) (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [100 x 100 mm 3.937 x 3.937 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	15 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	650 nm 0.026 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc.
EX-28B-PN	EMC Directive, RoHS Directive	45 to 115 mm 1.772 to 4.528 in with white non-glossy paper (100 x 100 mm 3.937 x 3.937 in), spot diameter dia. 5 mm dia. 0.197 in with setting distance 80 mm 3.150 in	Opaque, translucent or transparent object (Note) (Min. dia. 1 mm dia. 0.039 in copper wire at setting distance 80 mm 3.150 in) (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [100 x 100 mm 3.937 x 3.937 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	15 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	650 nm 0.026 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc.
EX-28B-C5	EMC Directive, RoHS Directive	45 to 115 mm 1.772 to 4.528 in with white non-glossy paper (100 x 100 mm 3.937 x 3.937 in), spot diameter dia. 5 mm dia. 0.197 in with setting distance 80 mm 3.150 in	Opaque, translucent or transparent object (Note) (Min. dia. 1 mm dia. 0.039 in copper wire at setting distance 80 mm 3.150 in) (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [100 x 100 mm 3.937 x 3.937 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	15 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	650 nm 0.026 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.		Adjusting screwdriver: 1 pc.
EX-29B-PN	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	RF-200 (Reflector): 1 pc Adjusting screwdriver: 1 pc
EX-22A-PN	EMC Directive, RoHS Directive	5 to 160 mm 0.197 to 6.299 in (Note) with white non-glossy paper (200 x 200 mm) (7.874 x 7.874 in) (Note) In case of using this product at a sensing range of 50 mm 1.969 in or less, take care that the sensitivity adjustment range becomes extremely narrow.	Opaque,translucent or transparent object (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [200 x 200 mm 7.874 x 7.874 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc
EX-22B-PN	EMC Directive, RoHS Directive	5 to 160 mm 0.197 to 6.299 in (Note) with white non-glossy paper (200 x 200 mm) (7.874 x 7.874 in) (Note) In case of using this product at a sensing range of 50 mm 1.969 in or less, take care that the sensitivity adjustment range becomes extremely narrow.	Opaque,translucent or transparent object (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [200 x 200 mm 7.874 x 7.874 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc

Models table for series Ultra-compact Photoelectric Sensor EX-20 Ver.2
Part No.	CE Marking Directive Compliance	Sensing Range	Sensing Object	Hysteresis	Repeatability (Perpendicular to Sensing Axis)	Supply Voltage	Current Consumption	Output	Output: Utilization Category	Output: Short-Circuit Protection	Response Time	Operation Indicator	Stability Indicator	Protection	Operation Mode Switch	Sensitivity Adjuster	Ambient Temperature	Ambient Humidity	Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Emitting Element	Emitting Element: Peak Emission Wavelength	Material	Cable	Cable Extension	Weight (Typ.)	Accessory
EX-29B-PN-Y	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc
EX-29B-Y	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc
EX-29B-Y-C5	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.		Adjusting screwdriver: 1 pc
EX-29A-Y-C5	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.		Adjusting screwdriver: 1 pc
EX-28B	EMC Directive, RoHS Directive	45 to 115 mm 1.772 to 4.528 in with white non-glossy paper (100 x 100 mm 3.937 x 3.937 in), spot diameter dia. 5 mm dia. 0.197 in with setting distance 80 mm 3.150 in	Opaque, translucent or transparent object (Note) (Min. dia. 1 mm dia. 0.039 in copper wire at setting distance 80 mm 3.150 in) (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [100 x 100 mm 3.937 x 3.937 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	15 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	650 nm 0.026 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc.
EX-28B-PN	EMC Directive, RoHS Directive	45 to 115 mm 1.772 to 4.528 in with white non-glossy paper (100 x 100 mm 3.937 x 3.937 in), spot diameter dia. 5 mm dia. 0.197 in with setting distance 80 mm 3.150 in	Opaque, translucent or transparent object (Note) (Min. dia. 1 mm dia. 0.039 in copper wire at setting distance 80 mm 3.150 in) (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [100 x 100 mm 3.937 x 3.937 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	15 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	650 nm 0.026 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc.
EX-28B-C5	EMC Directive, RoHS Directive	45 to 115 mm 1.772 to 4.528 in with white non-glossy paper (100 x 100 mm 3.937 x 3.937 in), spot diameter dia. 5 mm dia. 0.197 in with setting distance 80 mm 3.150 in	Opaque, translucent or transparent object (Note) (Min. dia. 1 mm dia. 0.039 in copper wire at setting distance 80 mm 3.150 in) (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [100 x 100 mm 3.937 x 3.937 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	15 mA or less	NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	650 nm 0.026 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.		Adjusting screwdriver: 1 pc.
EX-29B-PN	EMC Directive, RoHS Directive	30 to 200 mm 1.181 to 7.874 in (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.	dia. 15 mm dia. 0.591 in or more opaque or translucent object (Note) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque. (Note) Make sure to confirm detection with an actual sensor before use.	-	0.5 mm 0.020 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	RF-200 (Reflector): 1 pc Adjusting screwdriver: 1 pc
EX-22A-PN	EMC Directive, RoHS Directive	5 to 160 mm 0.197 to 6.299 in (Note) with white non-glossy paper (200 x 200 mm) (7.874 x 7.874 in) (Note) In case of using this product at a sensing range of 50 mm 1.969 in or less, take care that the sensitivity adjustment range becomes extremely narrow.	Opaque,translucent or transparent object (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [200 x 200 mm 7.874 x 7.874 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc
EX-22B-PN	EMC Directive, RoHS Directive	5 to 160 mm 0.197 to 6.299 in (Note) with white non-glossy paper (200 x 200 mm) (7.874 x 7.874 in) (Note) In case of using this product at a sensing range of 50 mm 1.969 in or less, take care that the sensitivity adjustment range becomes extremely narrow.	Opaque,translucent or transparent object (Note) Make sure to confirm detection with an actual sensor before use.	15 % or less of operation distance [200 x 200 mm 7.874 x 7.874 in with white non-glossy paper]	0.3 mm 0.012 in or less	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	13 mA or less	PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)	DC-12 or DC-13	Incorporated	0.5 ms or less	Orange LED (lights up when the output is ON)	Green LED (lights up under stable light received condition or stable dark condition)	IP67 (IEC)	-	Continuously variable adjuster	-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 3,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (modulated)	680 nm 0.027 mil	Enclosure: Polyethylene terephthalate Lens: Polyalylate	0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable.	Net weight: 20 g approx Gross weight: 45 g approx	Adjusting screwdriver: 1 pc

Ultra-compact Photoelectric Sensor EX-20 Ver.2

Part Number List