The EX-10 is a special Thru-Beam Sensor that was designed for two purposes; to check fluid levels and to detect the level of liquids containing water. The emitter on the EX-10 Sensor uses a particularly strong IR beam to not only penetrate transparent, but also semitransparent or colored containers such as PFA packages or shampoo bottles. Also, the sensitivity of the Sensor is adjustable to allow it to focus on a target, such as distinguishing foam from liquid in drinks, as an example.

Characteristics:

  • Suitable For Colored And Semitransparent Containers Or Packages
  • Not Affected By Droplets, Air Bubbles Or Foam
  • Compact Design
  • Short-Circuit Protected
  • Light ON/Dark ON
  • Sealed To IP67
  • M8 Plug-In Or Cable Connection (-J)
Series image for Water Detection Sensor EZ-10

Water Detection Sensor EZ-10

Part number list

Results 9
Models table for series Water Detection Sensor EZ-10
Part No.DatasheetCE Marking Directive ComplianceSensing Range Sensing Object Supply Voltage Current ConsumptionOutputOutput: Utilization Category Output: Output Operation Output: Short-Circuit ProtectionResponse TimeSensitivity AdjusterProtectionAmbient TemperatureAmbient HumidityAmbient IlluminanceVoltage WithstandabilityInsulation Resistance Vibration ResistanceShock ResistanceEmitting ElementMaterialWeight (Typ.)AccessoryDimensions
EMC Directive, RoHS Directive
5 m 16.404 ft (without container or pipe)
(Note):The sensing range shortens depending on the thickness, material, color, etc., of the container or pipe.
ø12 mm ø0.472 mm or more liquid which contains water, or opaque object
(Note):If there are two slit masks on both sides, the size of those slit masks represents the min. sensing object.
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
Emitter: 25 mA or less, Receiver: 25 mA or less
PNP open-collector transistor
・Maximum source current: 100 mA
・Applied voltage: 30 V DC or less (between output and +V)
・Residual voltage: 1.5 V or less (at 100 mA source current)
0.4 V or less (at 16 mA source current)
DC-12 or DC-13
Switchable either Light-ON or Dark-ON
Switchable either Light-ON or Dark-ON
12 ms or less
Continuously variable adjuster
IP67 (IEC)
0 to +55 ℃ +32 to +131℉ (No dew condensation allowed), Storage: -30 to +70 ℃ -22 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED (modulated)
Polycarbonate
Emitter: 45 g approx., Receiver: 50 g approx.
Adjusting screwdriver: 1 pc.
W12 x H31 x D20 mm W0.472 x H1.221 x D0.787 in
EMC Directive, RoHS Directive
5 m 16.404 ft (without container or pipe)
(Note):The sensing range shortens depending on the thickness, material, color, etc., of the container or pipe.
ø12 mm ø0.472 mm or more liquid which contains water, or opaque object
(Note):If there are two slit masks on both sides, the size of those slit masks represents the min. sensing object.
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
Emitter: 25 mA or less, Receiver: 25 mA or less
NPN open-collector transistor
・Maximum sink current: 100 mA
・Applied voltage: 30 V DC or less (between output and 0 V)
・Residual voltage: 1.5 V or less (at 100 mA sink current)
0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
Switchable either Light-ON or Dark-ON
Switchable either Light-ON or Dark-ON
12 ms or less
Continuously variable adjuster
IP67 (IEC)
0 to +55 ℃ +32 to +131℉ (No dew condensation allowed), Storage: -30 to +70 ℃ -22 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED (modulated)
Polycarbonate
Adjusting screwdriver: 1 pc.
W12 x H31 x D20 mm W0.472 x H1.221 x D0.787 in
EMC Directive, RoHS Directive
5 m 16.404 ft (without container or pipe)
(Note):The sensing range shortens depending on the thickness, material, color, etc., of the container or pipe.
ø12 mm ø0.472 mm or more liquid which contains water, or opaque object
(Note):If there are two slit masks on both sides, the size of those slit masks represents the min. sensing object.
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
Emitter: 25 mA or less, Receiver: 25 mA or less
NPN open-collector transistor
・Maximum sink current: 100 mA
・Applied voltage: 30 V DC or less (between output and 0 V)
・Residual voltage: 1.5 V or less (at 100 mA sink current)
0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
Switchable either Light-ON or Dark-ON
Switchable either Light-ON or Dark-ON
12 ms or less
Continuously variable adjuster
IP67 (IEC)
0 to +55 ℃ +32 to +131℉ (No dew condensation allowed), Storage: -30 to +70 ℃ -22 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED (modulated)
Polycarbonate
Adjusting screwdriver: 1 pc.
W12 x H31 x D20 mm W0.472 x H1.221 x D0.787 in
EMC Directive, RoHS Directive
5 m 16.404 ft (without container or pipe)
(Note):The sensing range shortens depending on the thickness, material, color, etc., of the container or pipe.
ø12 mm ø0.472 mm or more liquid which contains water, or opaque object
(Note):If there are two slit masks on both sides, the size of those slit masks represents the min. sensing object.
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
Emitter: 25 mA or less, Receiver: 25 mA or less
NPN open-collector transistor
・Maximum sink current: 100 mA
・Applied voltage: 30 V DC or less (between output and 0 V)
・Residual voltage: 1.5 V or less (at 100 mA sink current)
0.4 V or less (at 16 mA sink current)
DC-12 or DC-13
Switchable either Light-ON or Dark-ON
Switchable either Light-ON or Dark-ON
12 ms or less
Continuously variable adjuster
IP67 (IEC)
0 to +55 ℃ +32 to +131℉ (No dew condensation allowed), Storage: -30 to +70 ℃ -22 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED (modulated)
Polycarbonate
Emitter: 45 g approx., Receiver: 50 g approx.
Adjusting screwdriver: 1 pc.
W12 x H31 x D20 mm W0.472 x H1.221 x D0.787 in
EMC Directive, RoHS Directive
5 m 16.404 ft (without container or pipe)
(Note):The sensing range shortens depending on the thickness, material, color, etc., of the container or pipe.
ø12 mm ø0.472 mm or more liquid which contains water, or opaque object
(Note):If there are two slit masks on both sides, the size of those slit masks represents the min. sensing object.
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
Emitter: 25 mA or less, Receiver: 25 mA or less
PNP open-collector transistor
・Maximum source current: 100 mA
・Applied voltage: 30 V DC or less (between output and +V)
・Residual voltage: 1.5 V or less (at 100 mA source current)
0.4 V or less (at 16 mA source current)
DC-12 or DC-13
Switchable either Light-ON or Dark-ON
Switchable either Light-ON or Dark-ON
12 ms or less
Continuously variable adjuster
IP67 (IEC)
0 to +55 ℃ +32 to +131℉ (No dew condensation allowed), Storage: -30 to +70 ℃ -22 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Infrared LED (modulated)
Polycarbonate
Adjusting screwdriver: 1 pc.
W12 x H31 x D20 mm W0.472 x H1.221 x D0.787 in