| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | High functionality type | 47.3 mm 1.862 in | ±5 mm ±0.197 in | 1.5 μm 0.059 mil | ±0.2 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 1 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 0.39 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.1 Ć 0.1 mm 0.004 Ć 0.004 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ohm or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | RS-422 or RS-485 (selectable) Baud rate: 9,600/19,200/38,400/115,200/230,400/460,800/921,600 bps Data length 8 bit, Stop bit length 1 bit, Without parity check, BCC check, Termination code: CR | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 14-core cabtyre cable with connector, 0.5 m 1.640 ft long | Extension up to total 20 m 65.617 ft is possible with optional cable (Cable for standard type cannot be extended) . | Net weight: 70 g approx. (not including cable), 110 g approx. (including cable) Gross weight: 160 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic (specular reflection type: an aluminum vapor deposition surface reflection mirror) and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | Standard type | 85 mm 3.346 in | ± 20 mm ± 0.787 in | 2.5 μm 0.098 mil | ± 0.1 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 2 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 1 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.75 Ć 1.25 mm 0.030 x 0.049 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ī© or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 0.1mm2 10-core cabtyre cable, 5 m 16.404 ft long | | Net weight: 70 g approx. (not including cable), 320 g approx. (including cable) Gross weight: 380 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | Standard type | 50 mm 1.969 in | ± 10 mm ± 0.394 in | 1.5 μm 0.059 mil | ± 0.1 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 2 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 1 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.5 Ć 0.1 mm 0.020 x 0.039 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ī© or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 0.1mm2 10-core cabtyre cable, 5 m 16.404 ft long | | Net weight: 70 g approx. (not including cable), 320 g approx. (including cable) Gross weight: 380 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | High functionality type | 82.9 mm 3.264 in | ±10 mm ±0.394 in | 2.5 μm 0.098 mil | ±0.2 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 1 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 0.39 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.2 Ć 0.2 mm 0.008 Ć 0.008 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ohm or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | RS-422 or RS-485 (selectable) Baud rate: 9,600/19,200/38,400/115,200/230,400/460,800/921,600 bps Data length 8 bit, Stop bit length 1 bit, Without parity check, BCC check, Termination code: CR | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 14-core cabtyre cable with connector, 0.5 m 1.640 ft long | Extension up to total 20 m 65.617 ft is possible with optional cable (Cable for standard type cannot be extended) . | Net weight: 70 g approx. (not including cable), 110 g approx. (including cable) Gross weight: 160 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic (specular reflection type: an aluminum vapor deposition surface reflection mirror) and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | Standard type | 82.9 mm 3.264 in | ±10 mm ±0.394 in | 2.5 μm 0.098 mil | ±0.2 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 1 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 0.39 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.2 Ć 0.2 mm 0.008 Ć 0.008 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ohm or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 0.1mm2 10-core cabtyre cable, 5 m 16.404 ft long | | Net weight: 70 g approx. (not including cable), 320 g approx. (including cable) Gross weight: 380 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic (specular reflection type: an aluminum vapor deposition surface reflection mirror) and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | High functionality type | 85 mm 3.346 in | ± 20 mm ± 0.787 in | 2.5 μm 0.098 mil | ± 0.1 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 2 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 1 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.75 Ć 1.25 mm 0.030 x 0.049 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ī© or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | RS-422 or RS-485 (selectable) Baud rate: 9,600/19,200/38,400/115,200/230,400/460,800/921,600 bps Data length 8 bit, Stop bit length 1 bit, Without parity check, BCC check, Termination code: CR | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 14-core cabtyre cable with connector, 0.5 m 1.640 ft long | Extension up to total 20 m 65.617 ft is possible with optional cable. | Net weight: 70 g approx. (not including cable), 110 g approx. (including cable) Gross weight: 160 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | Standard type | 26.3mm 1.035 in | ±2 mm ±0.079 in | 0.5 μm 0.020 mil | ±0.2 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 1 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 0.39 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.1 Ć 0.1 mm 0.004 Ć 0.004 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ohm or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 0.1mm2 10-core cabtyre cable, 5 m 16.404 ft long | | Net weight: 70 g approx. (not including cable), 320 g approx. (including cable) Gross weight: 380 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of an aluminum vapor deposition surface reflection mirror and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | Standard type | 30 mm 1.181 in | ± 4 mm ± 0.157 in | 0.5 μm 0.020 mil | ± 0.1 % F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 2 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 1 mW (Peak emission wavelength: 655 nm 0.026 mil) | 0.1 Ć 0.1 mm 0.004 Ć 0.004 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ī© or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 0.1mm2 10-core cabtyre cable, 5 m 16.404 ft long | | Net weight: 70 g approx. (not including cable), 320 g approx. (including cable) Gross weight: 380 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | High functionality type | 250 mm 9.843 in | ±150 mm ±5.906 in | 20 μm 0.787 mil | ±0.3% F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 2 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 1 mW (Peak emission wavelength: 655 nm 0.026 mil) | 1.75 Ć 3.5 mm 0.069 Ć 0.138 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ohm or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | RS-422 or RS-485 (selectable) Baud rate: 9,600/19,200/38,400/115,200/230,400/460,800/921,600 bps Data length 8 bit, Stop bit length 1 bit, Without parity check, BCC check, Termination code: CR | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 14-core cabtyre cable with connector, 0.5 m 1.640 ft long | Extension up to total 20 m 65.617 ft is possible with optional cable (Cable for standard type cannot be extended) . | Net weight: 70 g approx. (not including cable), 110 g approx. (including cable) Gross weight: 160 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic and analog measurement values. |
| | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) | Standard type | 250 mm 9.843 in | ±150 mm ±5.906 in | 20 μm 0.787 mil | ±0.3% F.S. | ± 0.08 % F.S. / ā | Red semiconductor laser, Class 2 (IEC / JIS / FDA (Noteļ¼This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).) , Laser Notice No. 50) Max. output: 1 mW (Peak emission wavelength: 655 nm 0.026 mil) | 1.75 Ć 3.5 mm 0.069 Ć 0.138 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. | CMOS image sensor | 24 V DC ± 10 % including ripple 0.5 V (P-P) | 100 mA or less | 200 μs, 500 μs, 1 ms, 2 ms | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ohm or less | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector
-Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current)
-Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) | Opened when the amount of light is insufficient. | Incorporated (automatic restoration) | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. | | Green LED (lights up during laser emission) | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. | Three yellow LED | Red LED 5 digit display | 2 | 2,000 m 6561 ft or less | IP67 | -10 to +45 ā +14 to +113 ā (No dew condensation allowed), Storage: -20 to +60 ā -4 to +140 ā | 35 to 85 % RH, Storage: 35 to 85 % RH | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure | 1,000 V AC for one min. between all supply terminals connected together and enclosure | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each | Enclosure: PBT Front cover: Acrylic Cable: PVC | 0.1mm2 10-core cabtyre cable, 5 m 16.404 ft long | | Net weight: 70 g approx. (not including cable), 320 g approx. (including cable) Gross weight: 380 g approx. | Warning label: 1 set | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ā +68 ā, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic and analog measurement values. |