Safety Light Curtain Type 2 SF2B Ver.2

SF2B - Type 2 Safety Solution. The SF2B Series complies with international safety regulations at a reasonable cost.

From Area Sensors to Light Curtains, Panasonic provides the optimum device to solve critical safety applications.

Safety regulations throughout the world require different safety designs for various risk levels. The SF2B Series' design complies with IEC 61496 international safety standards and is also verified by a certified third-party organization. The SF2B Series is also available with new corner mirrors reducing setup work and wiring!

Characteristics

  • 32 Varieties For Finger And Arm Protection
  • High-Speed Response (Max. 15 ms)
  • No Dead Zone; Unit Height = Protective Height
  • OSSD1 And OSSD2 NPN / PNP Type Available
  • Error Code Display
  • Series Connection
  • Mutual Interference Prevention (ELCA)

Part Number List

Results 66
Models table for series Safety Light Curtain Type 2 SF2B Ver.2
Part No.DatasheetBeam PitchNo. of Beam ChannelsProtective Height Current ConsumptionPFH<sub>D</sub>MTTF<sub>D</sub>Weight (Total Of Emitter And Receiver)Applicable Standards: International StandardApplicable Standards: JapanApplicable Standards: North AmericaApplicable Standards: Europe (EU)CE Marking Directive ComplianceOperating RangeMin. Sensing ObjectEffective Aperture AnglePower Voltage Control Outputs (OSSD 1, OSSD 2)Control Outputs (OSSD1, OSSD2): Protection CircuitControl Outputs (OSSD 1, OSSD 2): Operation ModeAuxiliary Output (Aux)Response TimeAuxiliary Output (Aux): Operation ModeAuxiliary Output (Aux): Protection CircuitInterference Prevention FunctionSynchronization Method Emission Halt FunctionExternal Device Monitoring FunctionAmbient TemperatureAmbient HumidityEnvironmental Resistance: Degree of ProtectionEnvironmental Resistance: Dielectric Strength VoltageAmbient IlluminanceInsulation Resistance Vibration ResistanceShock ResistanceEmitting ElementCable ExtensionConnecting MethodMaterialAccessories
40 mm 1.575 in
18
712 mm 28.031 in
Emitter: 40 mA or less
Receiver: 60 mA or less
6.61 × 10-9
100 years or more
930 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
PNP open-collector transistor
- Max. source current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and +V]
- Residual voltage: 2.5 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
PNP open-collector transistor
- Max. source current: 60 mA
- Applied voltage: same as supply voltage [between the auxiliary output and +V]
- Residual voltage: 2.5 V or less (sink current 60 mA)(when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
40 mm 1.575 in
20
792 mm 31.181 in
Emitter: 45 mA or less
Receiver: 65 mA or less
6.68 × 10-9
100 years or more
1,000 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
PNP open-collector transistor
- Max. source current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and +V]
- Residual voltage: 2.5 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
PNP open-collector transistor
- Max. source current: 60 mA
- Applied voltage: same as supply voltage [between the auxiliary output and +V]
- Residual voltage: 2.5 V or less (sink current 60 mA)(when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
MS-SF2B-2(Intermediate supporting bracket):1 set
40 mm 1.575 in
18
712 mm 28.031 in
Emitter: 40 mA or less
Receiver: 60 mA or less
6.81 × 10-9
100 years or more
930 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
NPN open-collector transistor
- Max. sink current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and 0 V]
- Residual voltage: 2.0 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
NPN open-collector transistor
- Max. sink current: 60 mA
- Applied voltage: same as supply voltage[between the auxiliary output and 0 V]
- Residual voltage: 2.0 V or less (sink current 60 mA) (when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
40 mm 1.575 in
24
952 mm 37.480 in
Emitter: 45 mA or less
Receiver: 65 mA or less
6.87 × 10-9
100 years or more
1,300 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
PNP open-collector transistor
- Max. source current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and +V]
- Residual voltage: 2.5 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
PNP open-collector transistor
- Max. source current: 60 mA
- Applied voltage: same as supply voltage [between the auxiliary output and +V]
- Residual voltage: 2.5 V or less (sink current 60 mA)(when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
MS-SF2B-2(Intermediate supporting bracket):1 set
40 mm 1.575 in
16
632 mm 24.882 in
Emitter: 40 mA or less
Receiver: 60 mA or less
6.69 × 10-9
100 years or more
830 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
NPN open-collector transistor
- Max. sink current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and 0 V]
- Residual voltage: 2.0 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
NPN open-collector transistor
- Max. sink current: 60 mA
- Applied voltage: same as supply voltage[between the auxiliary output and 0 V]
- Residual voltage: 2.0 V or less (sink current 60 mA) (when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
40 mm 1.575 in
20
792 mm 31.181 in
Emitter: 45 mA or less
Receiver: 65 mA or less
6.88 × 10-9
100 years or more
1,000 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
NPN open-collector transistor
- Max. sink current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and 0 V]
- Residual voltage: 2.0 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
NPN open-collector transistor
- Max. sink current: 60 mA
- Applied voltage: same as supply voltage[between the auxiliary output and 0 V]
- Residual voltage: 2.0 V or less (sink current 60 mA) (when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
MS-SF2B-2(Intermediate supporting bracket):1 set
40 mm 1.575 in
28
1,112 mm 43.779 in
Emitter: 50 mA or less
Receiver: 75 mA or less
7.27 × 10-9
100 years or more
1,500 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
NPN open-collector transistor
- Max. sink current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and 0 V]
- Residual voltage: 2.0 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
NPN open-collector transistor
- Max. sink current: 60 mA
- Applied voltage: same as supply voltage[between the auxiliary output and 0 V]
- Residual voltage: 2.0 V or less (sink current 60 mA) (when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
MS-SF2B-2(Intermediate supporting bracket):1 set
40 mm 1.575 in
16
632 mm 24.882 in
Emitter: 40 mA or less
Receiver: 60 mA or less
6.48 × 10-9
100 years or more
830 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø47 mm ø1.850 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
PNP open-collector transistor
- Max. source current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and +V]
- Residual voltage: 2.5 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
PNP open-collector transistor
- Max. source current: 60 mA
- Applied voltage: same as supply voltage [between the auxiliary output and +V]
- Residual voltage: 2.5 V or less (sink current 60 mA)(when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
20 mm 0.787 in
12
232 mm 9.134 in
Emitter: 40 mA or less
Receiver: 50 mA or less
6.23 × 10-9
100 years or more
280 g approx.
IEC 61496-1/2 (Type 2), ISO 13849-1 (Category 2, PLc), IEC 61508-1 to 7 (SIL1)
JIS B 9704-1/2 (Type 2), JIS B 9705-1 (Category 2), JIS C 0508 (SIL1)
UL 61496-1/2 (Type 2), UL 508, UL 1998 (Class 1), CSA C22.2 No.14, CSA C22.2 No.0.8, OSHA 1910.212 (Note), OSHA 1910.217 (C) (Note), ANSI B11.1 to B11.19, ANSI/RIA 15.06
(Note) Not compatible when using the bottom cap cable SF2B-CB05-A.
EN 61496-1 (Type 2), EN 55011
Machinery Directive, EMC Directive, RoHS Directive
0.2 to 13 m 0.656 to 42.651 ft (0.2 to 5 m 0.656 to 16.404 ft when using the SF2B-CB05-B adapter cable)
ø27 mm ø1.063 in opaque object
plus or minus 5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)]
24 V DC plus or minus 15 % Ripple P-P 10 % or less
PNP open-collector transistor
- Max. source current: 200 mA
- Applied voltage: same as supply voltage [between the control output (OSSD 1, OSSD 2) and +V]
- Residual voltage: 2.5 V or less (sink current 200 mA) (when using 30.5 m 100.066 ft length cable)
Incorporated
ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the Safety Light Curtain or the synchronization signal)
PNP open-collector transistor
- Max. source current: 60 mA
- Applied voltage: same as supply voltage [between the auxiliary output and +V]
- Residual voltage: 2.5 V or less (sink current 60 mA)(when using 30.5 m 100.066 ft length cable)
(Note) When using auxiliary output (AUX), the SF2B-CB05-B adapter cable (optional) cannot be used.
OFF response: 15 ms or less
ON response: 40 to 60 ms
When using SF2B-CCBx or SF2B-CBx: OFF when OSSD ON, ON when OSSD OFF
When using SF2B-CB05-A: ON during normal operation, OFF when there is a problem with emitter operation or emission is halted
Incorporated
Incorporated
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
SF2B-Hx and SF2B-Ax can be used together. (Note 2)
[When using SF2B-CB05-B (optical synchronization):
- Series connection: 3 sets max. (Total 128 beam channels). (However, SF2B-Ax allows up to a total of 96 beam channels when two sets are connected, and up to 64 beam channels when three sets are connected). (Note 1)
- Parallel connection: 2 sets max.
- Series and parallel mixed connection: Series connection of 3 sets max. and parallel connection of 2 sets max. are simultaneously possible.
SF2B-Hx and SF2B-Ax can be used together. (Note 2)]
(Note 1) The SF2B-H8-x and SF2B-A4-x cannot be connected in series.
(Note 2) When making series connection mixing SF2B-Hx and SF2B-Ax, calculate by doubling the number of optical axes only for SF2B-Ax, and make the total number of optical axes fall below 128 axes.
(e.g.) When making series connection with SF2B-H36 and SF2B-A44, the total number of optical axes will be 124 axes. The number of optical axes for SF2B-H36 + (number of optical axes for SF2B-A44 × 2) = total number of optical axes. 36 optical axes + (44 optical axes × 2) = 124 optical axes.
Cable synchronization (optical synchronization when using SF2B-CB05-B)
Incorporated
Incorporated
-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: -25 to +70 ℃ -13 to +158 ℉
30 to 85 % RH, Storage: 30 to 95 % RH
IP65 (IEC) (*IP67 is later than Ver.2)
1,000 V AC for one min. between all supply terminals connected together and enclosure
Incandescent light: 3,500 lx or less at the light-receiving face
20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
Infrared LED (Peak emission wavelength: 870 nm 0.034 mil)
Extension up to total 30.5 m 100.066 ft is possible for both emitter and receiver, with optional mating cables.
Connector
Enclosure: Aluminium
Upper and lower edges : Die-cast zine alloy
Inner case: Polycarbonate / Polyester resin
Cap: PBT
SF2B-TR27 (Test rod): 1 No.