Compact Safety Light Curtain[Type4 PLe SIL3] SF4B-C

A Type 4 - Compact Safety Light Curtain With Improved Environmental Resistance

The Panasonic SF4B-C Compact Safety Light Curtains, with a thickness of only 20 x 27.4mm, come with an ultra-light housing. The combination of a plastic body with a metal inner frame is designed to minimize weight while at the same time increasing the toughness.

The SF4B-C Series is available as a hand protection type with a beam pitch of 20mm, allowing users to detect objects with a diameter as small as 25mm and the arm-protection type with its beam pitch of 40mm which can detect objects of 45mm and larger. Both types offer an operation range of up to 7m. Cable and Connector types are available.

Characteristics

Side Mounting Possible To Avoid Dead Zones
Very Light Weight Due To Combined Metal/Polycarbonate Housing
Compact Dimensions (20 X 27.4mm)
Large Multi-Purpose Indicator
PNP / NPN Polarity Switching
Beam Alignment Indicator
Interference Prevention Incorporated
IP65 Protection

Models table for series Compact Safety Light Curtain[Type4 PLe SIL3] SF4B-C
Part No.	No. of Beam Channels	Protective Height	Current Consumption	Current Consumption: Large Multipurpose Indicator Lights Off	Current Consumption: Large Multipurpose Indicator Lights Up	PFH<sub>D</sub>	MTTF<sub>D</sub>	Net Weight (Total of Emitter and Receiver)	Applicable Standards: International Standard	Applicable Standards: Japan	Applicable Standards: Europe (EU)	Applicable Standards: North America	Applicable Standards: South Korea (S-Mark)	CE Marking Directive Compliance	Operating Range	Beam Pitch	Min. Sensing Object	Effective Aperture Angle	Power Voltage	Control Outputs (OSSD 1, OSSD 2)	Control Outputs (OSSD 1, OSSD 2): Operation Mode	Control Outputs (OSSD1, OSSD2): Protection Circuit	Response Time	Auxiliary Output (Non-Safety Output)	Auxiliary Output (Non-Safety Output): Operation Mode	Auxiliary Output (Non-Safety Output): Protection Circuit	Muting Auxiliary Output:Operation Mode	Muting Auxiliary Output	Muting Auxiliary Output:Protection Circuit	ELCA Function	Emission Halt Function	Interlock Function	External Device Monitoring Function	Override Function	Muting Function	Large Multi-Purpose Indicator Function	Optional Functions	Pollution Degree	Operating Altitude	Environmental Resistance: Degree of Protection	Ambient Temperature	Ambient Humidity	Ambient Illuminance	Environmental Resistance: Dielectric Strength Voltage	Insulation Resistance	Vibration Resistance	Shock Resistance	Emitting Element	Material	Cable	Cable Extension	Accessories
SF4B-A12C	12	503.4 mm 19.819 in	Emitter: 60 mA or less Receiver: 70 mA or less			1.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 930 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	-
SF4B-A28CA-J05	28	1,143.4 mm 45.016 in		Emitter: 70 mA or less Receiver: 85 mA or less	Emitter: 80 mA or less Receiver: 95 mA or less	2.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,300 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-A16CA-J05	16	663.4 mm 26.118 in		Emitter: 65 mA or less Receiver: 75 mA or less	Emitter: 75 mA or less Receiver: 85 mA or less	2.2　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 750 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-A16C	16	663.4 mm 26.118 in	Emitter: 65 mA or less Receiver: 75 mA or less			2.2　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,100 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	-
SF4B-H20C	20	423.4 mm 16.669 in	Emitter: 65 mA or less Receiver: 75 mA or less			2.4　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 860 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, S2-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	20 mm 0.787 in	ø25 mm ø0.984 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	SF4B-TR25 (Test rod): 1 pc.
SF4B-H16CA-J05	16	343.4 mm 13.52 in		Emitter: 65 mA or less Receiver: 75 mA or less	Emitter: 75 mA or less Receiver: 85 mA or less	2.1　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 430 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, S2-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	20 mm 0.787 in	ø25 mm ø0.984 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	SF4B-TR25 (Test rod): 1 pc.
SF4B-A44CA-J05	44	1,783.4 mm 70.212 in		Emitter: 80 mA or less Receiver: 100 mA or less	Emitter: 90 mA or less Receiver: 110 mA or less	3.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,800 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-A36CA-J05	36	1,463.4 mm 57.614 in		Emitter: 75 mA or less Receiver: 95 mA or less	Emitter: 85 mA or less Receiver: 105 mA or less	3.4　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,600 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-H12CA-J05	12	263.4 mm 10.37 in		Emitter: 65 mA or less Receiver: 75 mA or less	Emitter: 75 mA or less Receiver: 85 mA or less	1.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 360 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, S2-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	20 mm 0.787 in	ø25 mm ø0.984 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	SF4B-TR25 (Test rod): 1 pc.
SF4B-A36C	36	1,463.4 mm 57.614 in	Emitter: 75 mA or less Receiver: 95 mA or less			3.4　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 2,000 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	-

Models table for series Compact Safety Light Curtain[Type4 PLe SIL3] SF4B-C
Part No.	No. of Beam Channels	Protective Height	Current Consumption	Current Consumption: Large Multipurpose Indicator Lights Off	Current Consumption: Large Multipurpose Indicator Lights Up	PFH<sub>D</sub>	MTTF<sub>D</sub>	Net Weight (Total of Emitter and Receiver)	Applicable Standards: International Standard	Applicable Standards: Japan	Applicable Standards: Europe (EU)	Applicable Standards: North America	Applicable Standards: South Korea (S-Mark)	CE Marking Directive Compliance	Operating Range	Beam Pitch	Min. Sensing Object	Effective Aperture Angle	Power Voltage	Control Outputs (OSSD 1, OSSD 2)	Control Outputs (OSSD 1, OSSD 2): Operation Mode	Control Outputs (OSSD1, OSSD2): Protection Circuit	Response Time	Auxiliary Output (Non-Safety Output)	Auxiliary Output (Non-Safety Output): Operation Mode	Auxiliary Output (Non-Safety Output): Protection Circuit	Muting Auxiliary Output:Operation Mode	Muting Auxiliary Output	Muting Auxiliary Output:Protection Circuit	ELCA Function	Emission Halt Function	Interlock Function	External Device Monitoring Function	Override Function	Muting Function	Large Multi-Purpose Indicator Function	Optional Functions	Pollution Degree	Operating Altitude	Environmental Resistance: Degree of Protection	Ambient Temperature	Ambient Humidity	Ambient Illuminance	Environmental Resistance: Dielectric Strength Voltage	Insulation Resistance	Vibration Resistance	Shock Resistance	Emitting Element	Material	Cable	Cable Extension	Accessories
SF4B-A12C	12	503.4 mm 19.819 in	Emitter: 60 mA or less Receiver: 70 mA or less			1.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 930 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	-
SF4B-A28CA-J05	28	1,143.4 mm 45.016 in		Emitter: 70 mA or less Receiver: 85 mA or less	Emitter: 80 mA or less Receiver: 95 mA or less	2.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,300 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-A16CA-J05	16	663.4 mm 26.118 in		Emitter: 65 mA or less Receiver: 75 mA or less	Emitter: 75 mA or less Receiver: 85 mA or less	2.2　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 750 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-A16C	16	663.4 mm 26.118 in	Emitter: 65 mA or less Receiver: 75 mA or less			2.2　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,100 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	-
SF4B-H20C	20	423.4 mm 16.669 in	Emitter: 65 mA or less Receiver: 75 mA or less			2.4　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 860 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, S2-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	20 mm 0.787 in	ø25 mm ø0.984 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	SF4B-TR25 (Test rod): 1 pc.
SF4B-H16CA-J05	16	343.4 mm 13.52 in		Emitter: 65 mA or less Receiver: 75 mA or less	Emitter: 75 mA or less Receiver: 85 mA or less	2.1　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 430 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, S2-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	20 mm 0.787 in	ø25 mm ø0.984 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	SF4B-TR25 (Test rod): 1 pc.
SF4B-A44CA-J05	44	1,783.4 mm 70.212 in		Emitter: 80 mA or less Receiver: 100 mA or less	Emitter: 90 mA or less Receiver: 110 mA or less	3.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,800 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-A36CA-J05	36	1,463.4 mm 57.614 in		Emitter: 75 mA or less Receiver: 95 mA or less	Emitter: 85 mA or less Receiver: 105 mA or less	3.4　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 1,600 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	-
SF4B-H12CA-J05	12	263.4 mm 10.37 in		Emitter: 65 mA or less Receiver: 75 mA or less	Emitter: 75 mA or less Receiver: 85 mA or less	1.9　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 360 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, S2-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	20 mm 0.787 in	ø25 mm ø0.984 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3Ωor less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	When muting auxiliary output: ON	NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable)	Incorporated	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	Incorporated	Incorporated	Incorporated	Muting setting changing, override setting changing, fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 12-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long	Extension up to total 50 m 164.042 ft is possible for both emitter and receiver optional mating cables	SF4B-TR25 (Test rod): 1 pc.
SF4B-A36C	36	1,463.4 mm 57.614 in	Emitter: 75 mA or less Receiver: 95 mA or less			3.4　× 10^-9 (Note) Probability of dangerous failure per hour.	100 years or more (Note) Mean time to dangerous failure.	approx. 2,000 g	IEC 61496-1 / 2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)	JIS B 9704-1 / 2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)	EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 (Note) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate.	ANSI / UL 61496-1 / 2 (Type 4), ANSI / UL 508, CAN / CSA 61496-1 / 2 (Type 4), CAN / CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI / RIA 15.06 (Note) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD America, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7	S1-G-35-2005, s²-W-11-2003	Machine Directive, EMC Directive, RoHS Directive	0.3 to 7m 0.984 to 22.966 ft (Note) The operating range is the possible setting distance between the emitter and the receiver.	40 mm 1.575 in	ø 45 mm ø 1.772 in opaque object (Note) In case the blanking function is valid, the operation mode is changed.	plus or minus 2.5℃ or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / ANSI/UL 61496-2) ]	24 V DC plus or minus 10 % Ripple P-P 10 % or less	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Applied voltage: Same as supply voltage (between the control output and +V) • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output and 0 V) • Residual voltage: 2.5 V or less (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF condition) • Maximum load capacity: : 0.22 micro F (No load to maximum output current) • Load wiring resistance: 3 Ω or less	ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the safety light curtain or the synchronization signal) (Note) During muting, control output will not turn off even if the beams are interrupted. (Note) When the blanking function is enabled, the operating mode will change.	Incorporated	OFF response: 14 ms or less ON response: 80 to 90 ms	PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and +V) • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 60 mA, when using 20 m 65.617 ft length cable)	OFF when control outputs are ON, ON when control outputs are OFF (Factory setting, operating mode can be changed using the SFB-HC handy-controller.)	Incorporated	-	-	-	Incorporated (reducing mutual interference automatically)	Incorporated	Incorporated [Manual reset / Auto reset] (Note) The manual reset and automatic reset are possible to be switched depending on the wiring status.	Incorporated	-	-	-	Fixed blanking, floating blanking, light emitting amount control, auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing (Note) In case of using optional function, the handy-controller SFB-HC is required.	3	2,000 m 6,561.68 ft or less (Note) Do not use or store in an environment pressurized to atmospheric pressure or higher at an altitude of 0 m.	IP65 (IEC)	-10 to +55℃ +14 to +131 ℉ (No dew condensation or icing allowed), Storage: –25 to +60 ℃ –3 to +140 ℉	30 to 85 % RH, Storage: 30 to 85 % RH	Incandescent light: 3,500 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each	300 m / s² acceleration (30 G approx.) in X, Y and Z directions for three times each	Infrared LED (Peak emission wavelength: 850 nm 0.033 mil)	Enclosure: Polycarbonate	0.15 mm² (power line: 0.2 mm²) 8-core heat-resistant PVC cable, 5 m 16.404 ft long	Extension up to total 50 m 164.042 ft is possible for 0.2 mm² or more, cable (Note) When the synchronization+ wire (orange) and synchronization- wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm² or more shielded twisted pair cable.	-

Compact Safety Light Curtain[Type4 PLe SIL3] SF4B-C

A Type 4 - Compact Safety Light Curtain With Improved Environmental Resistance

Characteristics

Part Number List