Laser Measurement Sensors: Ultra-compact Laser Collimated Beam Sensor HL-T1

Model List

Found 8 matches. Display 1 - 8 matches.
Part No.sort ascendingData SheetTypeCE marking directive complianceApplicable sensor headSupply voltageCurrent consumptionMeasuring cycleLinear outputLinear output : Temperature characteristicsSettable average sampling rateJudgment outputs (HIGH, PASS, LOW)Parts Inventory
   Column active Filter
Close

Filter by Type

Column active Filter
Close

Filter by CE marking directive compliance

Column active Filter
Close

Filter by Applicable sensor head

Column active Filter
Close

Filter by Supply voltage

Column active Filter
Close

Filter by Current consumption

Column active Filter
Close

Filter by Measuring cycle

Column active Filter
Close

Filter by Linear output

Column active Filter
Close

Filter by Linear output : Temperature characteristics

Column active Filter
Close

Filter by Settable average sampling rate

Column active Filter
Close

Filter by Judgment outputs (HIGH, PASS, LOW)

 
design engineersPanasonicHL-T1010F
Sensing width 10 mm 0.394 in typeEMC Directive, RoHS Directiven/an/an/an/an/an/an/an/a
design engineersPanasonicHL-T1010A
Sensing width 10 mm 0.394 in typeEMC Directive, RoHS Directiven/an/an/an/an/an/an/an/a
design engineersPanasonicHL-T1005F
Sensing width 5 mm 0.197 in typeEMC Directive, RoHS Directiven/an/an/an/an/an/an/an/a
design engineersPanasonicHL-T1005A
Sensing width 5 mm 0.197 in typeEMC Directive, RoHS Directiven/an/an/an/an/an/an/an/a
design engineersPanasonicHL-T1001F
Beam diameter dia.1 mm dia.0.039 in typeEMC Directive, RoHS Directiven/an/an/an/an/an/an/an/a
design engineersPanasonicHL-T1001A
Beam diameter dia.1 mm dia.0.039 in typeEMC Directive, RoHS Directiven/an/an/an/an/an/an/an/a
design engineersPanasonicHL-AC1P
PNP outputEMC Directive, RoHS DirectiveHL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less190 mA or less (when connected to the sensor head)150 micro sCurrent / voltage output switchable (Note)
-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm
-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm
(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)
(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller.
plus or minus 0.2 % F.S./℃
(Note) These are the temperature characteristics of the linear output when the sensor head is connected.
1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096
(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1).
PNP open-collector transistor
-Maximum source current: 50 mA
-Applied voltage: 30 V DC or less (between judgment output and +V)
-Residual voltage: 2 V or less (at 50 mA source current)
design engineersPanasonicHL-AC1
NPN outputEMC Directive, RoHS DirectiveHL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less190 mA or less (when connected to the sensor head)150 micro sCurrent / voltage output switchable (Note)
-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm
-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm
(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)
(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller.
plus or minus 0.2 % F.S./℃
(Note) These are the temperature characteristics of the linear output when the sensor head is connected.
1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096
(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1).
NPN open-collector transistor
-Maximum sink current: 50 mA
-Applied voltage: 30 V DC or less (between judgment output and 0 V)
-Residual voltage: 1.2 V or less (at 50 mA sink current)