Specifications

Specifications table for model FX-101P
ItemPerformance characteristics
CE Marking Directive ComplianceEMC Directive, RoHS Directive
Supply Voltage 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Power ConsumptionNormal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
OutputPNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1.5 V or less (at 100 mA source current)
Output: Output Operation Selectable either Light-ON or Dark-ON, at SET mode
Output: Short-Circuit ProtectionIncorporated
External InputPNP non-contact input
- Signal condition
High: +4 V to +V DC (Sink current 0.5 to 3 mA)
Low: 0 to +0.6 V DC or Open
- Input impedance: 10 kOhm approx.
Response TimeEmission frequency 0: 250 micro s or less (factory default setting)
Emission frequency 1: 450 micro s or less
Emission frequency 2: 500 micro s or less
Emission frequency 3: 600 micro s or less
Sensitivity Setting2-point teaching / Limit teaching / Full-auto teaching
Operation Indicator Orange LED (lights up when the output is ON)
Digital Display4 digits (green) + 4 digits (red) LCD display
Fine Sensitivity Adjustment FunctionIncorporated
Timer Function ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
Emission Amount Setting Function3-level + Auto setting (from production in December 2007)
Interference Prevention FunctionIncorporated Emission frequency selection method (Functions at emission frequency 1, 2 or 3)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting).
Ambient Temperature–10 to +55 ℃ +14 to +131
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 , if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158
Ambient Humidity35 to 85 % RH, Storage: 35 to 85 % RH
Ambient IlluminanceIncandescent light: 3,000 lx or less at the light-receiving face
Voltage Withstandability1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
Insulation Resistance20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
Vibration Resistance10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
Shock Resistance98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Emitting Element (Modulated)Red LED (Peak emission wavelength: 643 nm 0.025 mil)
MaterialEnclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connecting MethodConnector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Cable LengthTotal length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Weight (Typ.)Net weight: 15 g approx.
Gross weight: 35 g approx.
AccessoryFC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.

Stock check

Model image for FX-101P

FX-101P