LED Collimated Beam Sensor LA-300

LED Collimated Beam Type, which is as accurate as a Laser Sensor, but much safer.

Models table for series LED Collimated Beam Sensor LA-300
Part No.	Datasheet	CE Marking Directive Compliance	Type	Applicable Amplifiers	Beam Width	Sensing Range	Min. Sensing Object	Repeatability	Temperature Characteristics	Applicable Sensor Head	Supply Voltage	Current Consumption	Comparative Outputs (HIGH, LOW)	Comparative Outputs (HIGH, LOW): Utilization Category	Comparative Outputs (HIGH, LOW): Response Time	Comparative Outputs (HIGH, LOW): Output Operation	Comparative Outputs (HIGH, LOW): Short-Circuit Protection	Analog Output	Analog Output: Slew Rate	Analog Output: Temperature Characteristics	External Synchronization	Indicators: Power	Indicators: Stable Incident Beam	Indicators: Operation	Indicators: External Synchronization	Adjusters: Span	Adjusters: Shift	Adjusters: HIGH (Over-Dark) Level	Adjusters: LOW (Under-Dark) Level	Environmental Resistance: Ambient Temperature	Environmental Resistance: Ambient Humidity	Environmental Resistance: Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Environmental Resistance: Vibration Resistance	Environmental Resistance: Shock Resistance	Emitting Element	Material	Cable	Cable Extension	Weight (Typ.)	Accessory
LA-305		EMC Directive, RoHS Directive	Slim	LA-A1	5 mm 0.197 in	300 mm 11.811 in	ø0.05 mm ø0.002 in opaque object	Perpendicular to sensing axis: 0.01 mm 0.0004 in or less	0.2 % F.S./degrees or less																					0 to +40 ℃ +32 to +104℉ (No dew condensation), Storage: -20 to +70 ℃ -4 to +158℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (Peak emission wavelength 650 nm 0.026 mil, modulated)	Enclosure: Heat-resistant ABS Cover: Heat-resistant ABS Front cover: Glass	0.18 mm² 3-core composite cabtyre cable, 2 m 6.562 ft long	Extension up to total 10 m 32.808 ft is possible, for both emitter and receiver, with 0.18 mm², or more, cable. (Shield wire must be extended with shield wire.)	Emitter: 70 g approx., Receiver: 70 g approx.	MS-LA3-2 (Sensor head mounting bracket): 1 set for emitter and receiver, Target label: 2 pcs.
LA-A1		EMC Directive, RoHS Directive	NPN output type							LA-305	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	120 mA or less (including sensor heads)	NPN open-collector transistor -Maximum sink current: 100 mA -Applied voltage: 30 V DC or less (between comparative output and 0 V) -Residual voltage: 1.5 V or less (at 100 mA sink current), 0.5 V or less (at 16 mA sink current)	DC-12 or DC-13	0.5 ms or less	HIGH output: ON when the received beam level is equal to or lower than HIGH (Over-dark) level LOW output: ON when the received beam level is equal to or higher than LOW (Under-dark) level	Incorporated	Analog voltage Output voltage: 1 V (Darkest) to 5 V (Lightest) Output impedance: 75 Ohm	8 V/ms or more	0.05 % F.S./℃ or less	Incorporated (Either gate trigger or edge trigger is selectable)	Green LED (lights up when the power is ON)	Three green LEDs (light up in three stages in proportion to the amount of beam received)	Two orange LEDs (light up when High and Low comparative outputs are ON, respectively)	Green LED (lights up when the comparative outputs are effective)	15-turn adjuster sets the span for the analog output voltage	15-turn adjuster sets the offset for the analog output voltage	15-turn adjuster sets the HIGH output threshold level (Over-dark level)	15-turn adjuster sets the LOW output threshold level (Under-dark level)	0 to +50 ℃ +32 to +122℉ (No dew condensation), Storage: -20 to +70℃ -4 to +158℉	35 to 85 % RH, Storage: 35 to 85 % RH		1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each		Enclosure: Heat-resistant ABS Terminal cover: Heat-resistant ABS Front cover: Polycarbonate	0.22 mm² (shield wire: 0.15 mm²) 7-core composite cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.22 mm², or more, cable. (Shield wire must be extended with 0.15 mm², or more, shield wire.) (Note)This product is CE compliant and complies with EMC directives. EN 61000-6-2 is the applicable standard that covers immunities relating to use of this product, but in order to comply with this standard, the following conditions must be satisfied. Conditions The amplifier should be connected less than 10 m 32.808 ft from the power supply. The signal line to connect with the amplifier should be less than 30 m 98.425 ft.	Net weight: 200 g approx.	Adjusting screwdriver: 1 pc.

Models table for series LED Collimated Beam Sensor LA-300
Part No.	Datasheet	CE Marking Directive Compliance	Type	Applicable Amplifiers	Beam Width	Sensing Range	Min. Sensing Object	Repeatability	Temperature Characteristics	Applicable Sensor Head	Supply Voltage	Current Consumption	Comparative Outputs (HIGH, LOW)	Comparative Outputs (HIGH, LOW): Utilization Category	Comparative Outputs (HIGH, LOW): Response Time	Comparative Outputs (HIGH, LOW): Output Operation	Comparative Outputs (HIGH, LOW): Short-Circuit Protection	Analog Output	Analog Output: Slew Rate	Analog Output: Temperature Characteristics	External Synchronization	Indicators: Power	Indicators: Stable Incident Beam	Indicators: Operation	Indicators: External Synchronization	Adjusters: Span	Adjusters: Shift	Adjusters: HIGH (Over-Dark) Level	Adjusters: LOW (Under-Dark) Level	Environmental Resistance: Ambient Temperature	Environmental Resistance: Ambient Humidity	Environmental Resistance: Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Environmental Resistance: Vibration Resistance	Environmental Resistance: Shock Resistance	Emitting Element	Material	Cable	Cable Extension	Weight (Typ.)	Accessory
LA-305		EMC Directive, RoHS Directive	Slim	LA-A1	5 mm 0.197 in	300 mm 11.811 in	ø0.05 mm ø0.002 in opaque object	Perpendicular to sensing axis: 0.01 mm 0.0004 in or less	0.2 % F.S./degrees or less																					0 to +40 ℃ +32 to +104℉ (No dew condensation), Storage: -20 to +70 ℃ -4 to +158℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 lx or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each	Red LED (Peak emission wavelength 650 nm 0.026 mil, modulated)	Enclosure: Heat-resistant ABS Cover: Heat-resistant ABS Front cover: Glass	0.18 mm² 3-core composite cabtyre cable, 2 m 6.562 ft long	Extension up to total 10 m 32.808 ft is possible, for both emitter and receiver, with 0.18 mm², or more, cable. (Shield wire must be extended with shield wire.)	Emitter: 70 g approx., Receiver: 70 g approx.	MS-LA3-2 (Sensor head mounting bracket): 1 set for emitter and receiver, Target label: 2 pcs.
LA-A1		EMC Directive, RoHS Directive	NPN output type							LA-305	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	120 mA or less (including sensor heads)	NPN open-collector transistor -Maximum sink current: 100 mA -Applied voltage: 30 V DC or less (between comparative output and 0 V) -Residual voltage: 1.5 V or less (at 100 mA sink current), 0.5 V or less (at 16 mA sink current)	DC-12 or DC-13	0.5 ms or less	HIGH output: ON when the received beam level is equal to or lower than HIGH (Over-dark) level LOW output: ON when the received beam level is equal to or higher than LOW (Under-dark) level	Incorporated	Analog voltage Output voltage: 1 V (Darkest) to 5 V (Lightest) Output impedance: 75 Ohm	8 V/ms or more	0.05 % F.S./℃ or less	Incorporated (Either gate trigger or edge trigger is selectable)	Green LED (lights up when the power is ON)	Three green LEDs (light up in three stages in proportion to the amount of beam received)	Two orange LEDs (light up when High and Low comparative outputs are ON, respectively)	Green LED (lights up when the comparative outputs are effective)	15-turn adjuster sets the span for the analog output voltage	15-turn adjuster sets the offset for the analog output voltage	15-turn adjuster sets the HIGH output threshold level (Over-dark level)	15-turn adjuster sets the LOW output threshold level (Under-dark level)	0 to +50 ℃ +32 to +122℉ (No dew condensation), Storage: -20 to +70℃ -4 to +158℉	35 to 85 % RH, Storage: 35 to 85 % RH		1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions three times each		Enclosure: Heat-resistant ABS Terminal cover: Heat-resistant ABS Front cover: Polycarbonate	0.22 mm² (shield wire: 0.15 mm²) 7-core composite cabtyre cable, 2 m 6.562 ft long	Extension up to total 50 m 164.042 ft is possible with 0.22 mm², or more, cable. (Shield wire must be extended with 0.15 mm², or more, shield wire.) (Note)This product is CE compliant and complies with EMC directives. EN 61000-6-2 is the applicable standard that covers immunities relating to use of this product, but in order to comply with this standard, the following conditions must be satisfied. Conditions The amplifier should be connected less than 10 m 32.808 ft from the power supply. The signal line to connect with the amplifier should be less than 30 m 98.425 ft.	Net weight: 200 g approx.	Adjusting screwdriver: 1 pc.