Specification

Specifications table for model GP-XC22KL
ItemPerformance characteristics
TypeThreaded type For 10 mm 0.394 in sensing
CE Marking Directive ComplianceEMC Directive, RoHS Directive
Supply Voltage 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Current Consumption150 mA or less
Resolution0.02 % F.S. (64 times average processing)
(Note) This value was obtained at a constant +25 ℃ +77 ℉ .
Sampling Frequency40 kHz (25 micro s)
LinearityWithin plus or minus 0.3 % F.S.
(Note) This value was obtained at a constant +25 ℃ +77 ℉ .
Temperature Characteristics 0.07 % F.S./℃ or less
(Note) This value represents 20 to 60 % of the maximum sensing distance when combining the sensor head and the controller.
Analog Voltage OutputsOutput voltage: -5 to +5 V (Note1) , Output impedance: 100 Ω approx.(Note2)
(Note1: Adjusted to a 0 to +5 V factory setting.)
(Note2:When using the BCD output unit GP-XBCD, the analog voltage output of a controller becomes invalid.)
Analog Voltage Outputs: Response Time75 micro s (maximum speed)
Comparative Outputs (HI, GO, LO)NPN open-collector transistor
-Maximum sink current: 100 mA
-Applied voltage: 30 V DC or less
(between comparative output and 0 V)
-Residual voltage: 1.6 V or less (at 100 mA sink current), 0.4 V or less (at 16 mA sink current)
Comparative Outputs (HI, GO, LO): Utilization CategoryDC-12 or DC-13
Comparative Outputs (HI, GO, LO): Output NumberHI / GO / LO 3 value output
Comparative Outputs (HI, GO, LO): Output OperationHI: ON when measured value > the upper limit value
GO: ON when upper limit value >= measured value >= lower limit value
LO: ON when lower limit value > measured value
Comparative Outputs (HI, GO, LO): Short-Circuit ProtectionIncorporated
External InputPhoto-coupler input
- Input current: 9 mA or less
- Operating voltage: ON voltage 17 V or more (between +24 V and input), OFF voltage 4 V or less (between +24 V and input)
- Input impedance: 5 kΩ approx.
Serial I/ORS-232C
Zero-Set Setting MethodPush button setting / External input setting
Indicators: ModeOrange LED (lights up when in mode status)
Indicators: HIOrange LED (lights up when the upper limit value is exceeded)
Indicators: GOGreen LED (lights up when within the upper and lower limit value)
Indicators: LO Orange LED (lights up when less than the lower limit value)
Indicators: TimingGreen LED (lights up as per the external or internal trigger timing)
Upper Level Digital Display Part5 digit orange LED (display of numerical values out of upper and lower limit value)
Lower Level Digital Display Part5 digit green LED (display of numerical values within the upper and lower limit value)
Pollution Degree 3 (Industrial environment)
Ambient Temperature-10 to +55 ℃ +14 to +131 ℉ , Storage: -20 to +70 ℃ -4 to +158 ℉
Ambient Humidity35 to 85 % RH, Storage: 35 to 85 % RH
Vibration Resistance10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each
Shock Resistance100 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
MaterialEnclosure: Polycarbonate
Weight (Typ.)Net weight: 120 g approx.
AccessoryATA4811 (Controller mounting frame): 1 set
Sensing Range0 to 10 mm 0 to 0.394 in
(Note) The sensing range is specified for the standard sensing object.
ProtectionIP67 (IEC), IP67g (Note:If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil. Please check the resistivity of the sensor against the cutting oil you are using beforehand.)
Standard Sensing ObjectStainless steel (SUS304) / Iron sheet [Cold rolled carbon steel (SPCC)] 60 x 60 x t 1 mm 2.362 x 2.362 x t 0.039 in
Voltage Withstandability250 V AC for one min. between all supply terminals connected together and enclosure
Insulation Resistance20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
CK Resistance500 m/s2 acceleration (50 G approx.) in X, Y and Z directions five times each
EnclosureBrass (Nickel plated)
Cable ProtectorPP
Sensing Part PA
CableHigh frequency coaxial cable with connector, 3 m 9.843 ft long
(Note) For the flexible cable type, please contact our office.
Cable ExtensionExtension up to total 10 m 32.808 ft is possible with the optional cable.
AccessoriesNut: 2 pcs.
Toothed lock washer: 1 pc.
Net Weight 80 g approx.
(Note) The given weight of the threaded type sensor head is the value including the weight of the nuts and the toothed lock washer.

Stock Check

Important

The service is owned, operated, controlled and managed by Panasonic's distributors.

For pricing, delivery and technical questions related to this service, please direct to them.

Panasonic assumes no responsibility for any dealings you may have with distributors.