Like the EX-10 Series, with the dimensions of only 14.5 x 3.5 x 10mm, the EX-10S Series Amplifier Built-In Ultra-Slim Photoelectric Sensors are among the smallest and narrowest Sensors worldwide. This "S" version with a thinner beam allows the detection of small objects within a very narrow detection zone.
Characteristics:
An Installation Closely Attached To Each Other Is Possible Due To Thin Beam
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 1.0 mm dia. 0.039 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current),1 V or less (at 16 mA sink current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 0.5 mm dia. 0.020 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 1.0 mm dia. 0.039 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current),1 V or less (at 16 mA sink current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current),1 V or less (at 16 mA sink current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 1.0 mm dia. 0.039 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 0.5 mm dia. 0.020 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
UL certification
Models table for series Amplifier built-in Ultra-slim Photoelectric Sensor EX-10S
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 1.0 mm dia. 0.039 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current),1 V or less (at 16 mA sink current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 0.5 mm dia. 0.020 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 1.0 mm dia. 0.039 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current),1 V or less (at 16 mA sink current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 2.0 mm dia. 0.078 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
NPN open-collector transistor - Maximum sink current: 50 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 2 V or less (at 50 mA sink current),1 V or less (at 16 mA sink current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 1.0 mm dia. 0.039 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.
dia. 0.5 mm dia. 0.020 in opaque object (Completely beam interrupted object) (Note) : The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
-
0.05 mm 0.002 in or less
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 10 mA or less Receiver: 10 mA or less
PNP open-collector transistor - Maximum source current: 50 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 2 V or less (at 50 mA source current), 1 V or less (at 16 mA source current)
DC-12 or DC-13
Incorporated
0.5 ms or less
Orange LED (lights up when the output is ON)
-
Green LED (lights up under stable light received condition or stable dark condition)
3 (Industrial environment)
IP67 (IEC)
-25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 lx at the light-receiving face
EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (20 G max.) in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (emitter and receiver). (Note) : For safety applications, do not exceed 30 m 98.425 ft.
Net weight (each emitter and receiver): 20 g approx Gross weight: 50 g approx
Mounting screws: 1 set
・EMC Directive ： EN 60947-5-2 ・RoHS Directive ・ISO 13849-1 (Category 1, PLc) (Note) (Note) : Conformed from December 2021 production.