Perpendicular to sensing axis: 0.01 mm 0.0004 in or less
0.2 % F.S./degrees or less
0 to +40 ℃ +32 to +104℉ (No dew condensation), Storage: -20 to +70 ℃ -4 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 10,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Red LED (Peak emission wavelength 650 nm 0.026 mil, modulated)
Enclosure: Heat-resistant ABS Cover: Heat-resistant ABS Front cover: Glass
0.18 mm2 3-core composite cabtyre cable, 2 m 6.562 ft long
Extension up to total 10 m 32.808 ft is possible, for both emitter and receiver, with 0.18 mm2, or more, cable. (Shield wire must be extended with shield wire.)
Emitter: 70 g approx., Receiver: 70 g approx.
MS-LA3-2 (Sensor head mounting bracket): 1 set for emitter and receiver, Target label: 2 pcs.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
120 mA or less (including sensor heads)
NPN open-collector transistor -Maximum sink current: 100 mA -Applied voltage: 30 V DC or less (between comparative output and 0 V) -Residual voltage: 1.5 V or less (at 100 mA sink current), 0.5 V or less (at 16 mA sink current)
DC-12 or DC-13
0.5 ms or less
HIGH output: ON when the received beam level is equal to or lower than HIGH (Over-dark) level LOW output: ON when the received beam level is equal to or higher than LOW (Under-dark) level
Incorporated
Analog voltage Output voltage: 1 V (Darkest) to 5 V (Lightest) Output impedance: 75 Ohm
8 V/ms or more
0.05 % F.S./℃ or less
Incorporated (Either gate trigger or edge trigger is selectable)
Green LED (lights up when the power is ON)
Three green LEDs (light up in three stages in proportion to the amount of beam received)
Two orange LEDs (light up when High and Low comparative outputs are ON, respectively)
Green LED (lights up when the comparative outputs are effective)
15-turn adjuster sets the span for the analog output voltage
15-turn adjuster sets the offset for the analog output voltage
15-turn adjuster sets the HIGH output threshold level (Over-dark level)
15-turn adjuster sets the LOW output threshold level (Under-dark level)
0 to +50 ℃ +32 to +122℉ (No dew condensation), Storage: -20 to +70℃ -4 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Enclosure: Heat-resistant ABS Terminal cover: Heat-resistant ABS Front cover: Polycarbonate
0.22 mm2 (shield wire: 0.15 mm2) 7-core composite cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164.042 ft is possible with 0.22 mm2, or more, cable. (Shield wire must be extended with 0.15 mm2, or more, shield wire.) (Note)This product is CE compliant and complies with EMC directives. EN 61000-6-2 is the applicable standard that covers immunities relating to use of this product, but in order to comply with this standard, the following conditions must be satisfied.
Conditions The amplifier should be connected less than 10 m 32.808 ft from the power supply. The signal line to connect with the amplifier should be less than 30 m 98.425 ft.
Net weight: 200 g approx.
Adjusting screwdriver: 1 pc.
Models table for series LED Collimated Beam Sensor LA-300
Perpendicular to sensing axis: 0.01 mm 0.0004 in or less
0.2 % F.S./degrees or less
0 to +40 ℃ +32 to +104℉ (No dew condensation), Storage: -20 to +70 ℃ -4 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 10,000 lx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Red LED (Peak emission wavelength 650 nm 0.026 mil, modulated)
Enclosure: Heat-resistant ABS Cover: Heat-resistant ABS Front cover: Glass
0.18 mm2 3-core composite cabtyre cable, 2 m 6.562 ft long
Extension up to total 10 m 32.808 ft is possible, for both emitter and receiver, with 0.18 mm2, or more, cable. (Shield wire must be extended with shield wire.)
Emitter: 70 g approx., Receiver: 70 g approx.
MS-LA3-2 (Sensor head mounting bracket): 1 set for emitter and receiver, Target label: 2 pcs.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
120 mA or less (including sensor heads)
NPN open-collector transistor -Maximum sink current: 100 mA -Applied voltage: 30 V DC or less (between comparative output and 0 V) -Residual voltage: 1.5 V or less (at 100 mA sink current), 0.5 V or less (at 16 mA sink current)
DC-12 or DC-13
0.5 ms or less
HIGH output: ON when the received beam level is equal to or lower than HIGH (Over-dark) level LOW output: ON when the received beam level is equal to or higher than LOW (Under-dark) level
Incorporated
Analog voltage Output voltage: 1 V (Darkest) to 5 V (Lightest) Output impedance: 75 Ohm
8 V/ms or more
0.05 % F.S./℃ or less
Incorporated (Either gate trigger or edge trigger is selectable)
Green LED (lights up when the power is ON)
Three green LEDs (light up in three stages in proportion to the amount of beam received)
Two orange LEDs (light up when High and Low comparative outputs are ON, respectively)
Green LED (lights up when the comparative outputs are effective)
15-turn adjuster sets the span for the analog output voltage
15-turn adjuster sets the offset for the analog output voltage
15-turn adjuster sets the HIGH output threshold level (Over-dark level)
15-turn adjuster sets the LOW output threshold level (Under-dark level)
0 to +50 ℃ +32 to +122℉ (No dew condensation), Storage: -20 to +70℃ -4 to +158℉
35 to 85 % RH, Storage: 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ , or more, with 250 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Enclosure: Heat-resistant ABS Terminal cover: Heat-resistant ABS Front cover: Polycarbonate
0.22 mm2 (shield wire: 0.15 mm2) 7-core composite cabtyre cable, 2 m 6.562 ft long
Extension up to total 50 m 164.042 ft is possible with 0.22 mm2, or more, cable. (Shield wire must be extended with 0.15 mm2, or more, shield wire.) (Note)This product is CE compliant and complies with EMC directives. EN 61000-6-2 is the applicable standard that covers immunities relating to use of this product, but in order to comply with this standard, the following conditions must be satisfied.
Conditions The amplifier should be connected less than 10 m 32.808 ft from the power supply. The signal line to connect with the amplifier should be less than 30 m 98.425 ft.