Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100

Series image for Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100

Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100

Part number list

Results 32
Models table for series Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100
Part No.DatasheetCE Marking Directive ComplianceType of Pressure Rated Pressure Range Pressure WithstandabilityApplicable FluidSupply Voltage Current ConsumptionAnalog Voltage OutputProtectionAmbient TemperatureAmbient HumidityVoltage WithstandabilityInsulation Resistance Vibration ResistanceShock ResistanceTemperature Characteristics Pressure Port MaterialConnecting MethodCableCable ExtensionWeight: Net WeightWeight: Gross WeightAccessoriesRemark
EMC Directive, RoHS Directive
Gauge pressure
-100.0 to +100.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M3 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
-100.0 to +100.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
-100.0 to +100.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M3 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
-100.0 to +100.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M5 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to +1.000 MPa
1.5 MPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M5 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
-100.0 to +100.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to +1.000 MPa
1.5 MPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
M3 male thread (for installing gasket)
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 6 g approx. / Cable 40 g approx.
70 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.
EMC Directive, RoHS Directive
Gauge pressure
0 to -101.0 kPa
500 kPa
Air, non-corrosive gas
12 to 24 V DC ± 10 % Ripple P-P 10 % or less
15 mA or less
Output voltage : 1 to 5 V (over rated pressure range)
Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type)
within 3 V ± 3 % F.S. (compound pressure type)
Span : within 4 V ± 3.5 % F.S.
Linearity : within ±0.5 % F.S.
Output impedance : 1 kΩ approx.
IP40 (IEC)
0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage : 35 to 85 % RH
1,000 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each
1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions for three times each
Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉
R1/8 male thread + M5 female thread.
Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR
Pressure element : Silicon diaphragm, PPS
Connector
0.2 mm2 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)
Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable.
Head 10 g approx. / Cable 40 g approx.
80 g approx.
Connector (e-CON) : 1 pc.
Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉.
The sensor head can be used independently.