Dual Display Digital Pressure Sensor [For Gas] DP-100L

Panasonic’s compact DP-100L Pressure Sensor with IO-Link features an improved digital display that offers increased clarity and a wider viewing angle. Thanks to a redesign of its circuitry, the low-power-consumption DP-100L Series requires 14% less power during normal operation and when operating in ECO / FULL mode the display is completely shut off for an increased power savings of up to 50% compared to normal operation. The current value and the threshold value can be checked at the same time, so the threshold value can be set and checked smoothly without switching to another screen mode.

CHARACTERISTICS

IO-Link Ready
Preprogrammed Self-diagnosis Function
Dual Display with 12-segment Font
High resolution and Performance

Preprogrammed Self-diagnosis Function

The self-diagnosis function of the DP-100L reports both sensor data and physical condition of the sensor to the host device through the I/O Link master. This allows the user to immediately judge the state of the sensor and easily identify the cause of failure.

Dual Display with 12-segment Font

Both the measured value and the threshold value can be monitored simultaneously on a single screen. The high-contrast 12-segment alphanumeric display improves the visual recognition of letters and numbers.

High Resolution and Performance

The low-pressure type DP-100L displays measurements in 0.1 kPa increments at a resolution of 1/2,000 and has a response time of 2.5 ms (variable up to 5,000 ms), ±0.5 % F.S. temperature characteristics, and ±0.1 % F.S. repeatability.

IO-Link Ready

The IO-Link interface of the DP-100L enables the user to exclusively control and configure the sensor through an external interface (PLC). The user will also be able to collect field data and monitor the physical condition of the sensor for predictive maintenance.

Models table for series Dual Display Digital Pressure Sensor [For Gas] DP-100L
Part No.	Regulatory Compliance and Certification	Type of Pressure	Rated Pressure Range	Set Pressure Range	Pressure Withstandability	Applicable Fluid	Supply Voltage	Power Consumption	Communication Output (C/Q): IO-Link Communication	Communication Output (C/Q): Baud Rate	Communication Output (C/Q): Process Data	Communication Output (C/Q): Minimum Cycle Time	Control Output (DO)	Control Output (DO): Output Operation	Control Output (DO): Output Operation Output Modes US	Control Output (DO): Hysteresis	Control Output (DO): Repeatability	Control Output (DO): Response Time	Control Output (DO): Short-Circuit Protection	Display	Display: Displayable Pressure Range	Output Indicator	Protection	Ambient Temperature	Ambient Humidity	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Temperature Characteristics	Pressure Port	Material	Connecting Method	Cable Length	Weight (Typ.)	Accessories	Remark
DP-101ZL3-M-P	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	−100.0 to +100.0 kPa	-101.0 to +101.0kPa	500kPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.1 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-101.0 to +101.0 kPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±0.5 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 125 g approx.	CN-14A-C2 (Connector attached cable 2 m 6.562 ft): 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.
DP-102ZL3-M-P-C	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	-0.100 to +1.000 Mpa	-0.101 to +1.010MPa	1.5MPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.2 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-0.101 to +1.010MPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±1 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 95 g approx.	Dedicated M12 connector cable, 0.3 m 0.984 ft long: 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.
DP-101ZL3-M-P-C	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	−100.0 to +100.0 kPa	-101.0 to +101.0kPa	500kPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.1 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-101.0 to +101.0 kPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±0.5 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 95 g approx.	Dedicated M12 connector cable, 0.3 m 0.984 ft long: 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.
DP-102ZL3-M-P	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	-0.100 to +1.000 Mpa	-0.101 to +1.010MPa	1.5MPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.2 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-0.101 to +1.010MPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±1 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 125 g approx.	CN-14A-C2 (Connector attached cable 2 m 6.562 ft): 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.

Models table for series Dual Display Digital Pressure Sensor [For Gas] DP-100L
Part No.	Regulatory Compliance and Certification	Type of Pressure	Rated Pressure Range	Set Pressure Range	Pressure Withstandability	Applicable Fluid	Supply Voltage	Power Consumption	Communication Output (C/Q): IO-Link Communication	Communication Output (C/Q): Baud Rate	Communication Output (C/Q): Process Data	Communication Output (C/Q): Minimum Cycle Time	Control Output (DO)	Control Output (DO): Output Operation	Control Output (DO): Output Operation Output Modes US	Control Output (DO): Hysteresis	Control Output (DO): Repeatability	Control Output (DO): Response Time	Control Output (DO): Short-Circuit Protection	Display	Display: Displayable Pressure Range	Output Indicator	Protection	Ambient Temperature	Ambient Humidity	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Temperature Characteristics	Pressure Port	Material	Connecting Method	Cable Length	Weight (Typ.)	Accessories	Remark
DP-101ZL3-M-P	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	−100.0 to +100.0 kPa	-101.0 to +101.0kPa	500kPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.1 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-101.0 to +101.0 kPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±0.5 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 125 g approx.	CN-14A-C2 (Connector attached cable 2 m 6.562 ft): 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.
DP-102ZL3-M-P-C	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	-0.100 to +1.000 Mpa	-0.101 to +1.010MPa	1.5MPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.2 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-0.101 to +1.010MPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±1 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 95 g approx.	Dedicated M12 connector cable, 0.3 m 0.984 ft long: 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.
DP-101ZL3-M-P-C	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	−100.0 to +100.0 kPa	-101.0 to +101.0kPa	500kPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.1 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-101.0 to +101.0 kPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±0.5 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 95 g approx.	Dedicated M12 connector cable, 0.3 m 0.984 ft long: 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.
DP-102ZL3-M-P	EMC Directive, RoHS Directive, UL/c-UL Certification	Gauge pressure	-0.100 to +1.000 Mpa	-0.101 to +1.010MPa	1.5MPa	Non-corrosive gas	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage) 360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)	IO-Link Specification V1.1 (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	COM3 (230.4 kbps) (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	4 byte (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	1.0ms (Note:)When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).	PNP open-collector transistor •Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (at 50 mA source current)	N.O./N.C. (selectable by key operation)	EASY mode / Hysteresis mode / Window comparator mode	Minimum 1 digit (variable)	±0.2 % F.S. (within ±2 digits)	2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation	Incorporated	4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)	-0.101 to +1.010MPa	Orange LED(Output operation indicator 1: Flashes during IO-Link communication, Lights up when the control output is ON during non-IO-Link communication (synchronized with the output operation indicator 2) Output operation indicator 2: Lights up when the control output is ON)	IP40(IEC）	−10 to +50℃ +14 to +122 ℉(No dew condensation or icing allowed), Storage: −10 to +60℃ +14 to +140 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in double amplitude or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each(when panel or flat attachment is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 49 m/s², in X, Y and Z directions for two hours each)	100 m/s² acceleration (10 G approx.) in X, Y and Z directions three times each	Within ±1 % F.S. (at +20℃ +68℉)	M5 female thread	Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber	Connector	Total length up to 20 m 65.617 ft (Condition of CE compliance less than 20 m 65.617 ft) is possible with 0.3 mm², or more, cable.	Net weight: 30 g approx., Gross weight: 125 g approx.	CN-14A-C2 (Connector attached cable 2 m 6.562 ft): 1 pc.	(Note:)measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20℃ +68℉.