Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100

The DPS-400 Pressure Sensors were designed to meet the specific requirements needed at today's production sites such as miniaturization of Sensors to facilitate the downsizing of equipment, convenient shape to better fit into their machines and efficient set-up functions that can help reduce the man-hours spent on replacements.

Models table for series Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100
Part No.	CE Marking Directive Compliance	Type of Pressure	Rated Pressure Range	Pressure Withstandability	Applicable Fluid	Supply Voltage	Current Consumption	Analog Voltage Output	Protection	Ambient Temperature	Ambient Humidity	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Temperature Characteristics	Pressure Port	Material	Connecting Method	Cable	Cable Extension	Weight: Net Weight	Weight: Gross Weight	Accessories	Remark
DPH-102	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-102-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-M3-R-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M3 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-102-M5-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M5 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-M3	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M3 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-M5-R-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M5 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-R	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-102-M5-R-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M5 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.

Models table for series Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100
Part No.	CE Marking Directive Compliance	Type of Pressure	Rated Pressure Range	Pressure Withstandability	Applicable Fluid	Supply Voltage	Current Consumption	Analog Voltage Output	Protection	Ambient Temperature	Ambient Humidity	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Temperature Characteristics	Pressure Port	Material	Connecting Method	Cable	Cable Extension	Weight: Net Weight	Weight: Gross Weight	Accessories	Remark
DPH-102	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-102-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-M3-R-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M3 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-102-M5-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M5 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-M3	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M3 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-M5-R-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M5 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103-R	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-103	EMC Directive, RoHS Directive	Gauge pressure	0 to -101.0 kPa	500 kPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	R¹/₈ male thread + M5 female thread.	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 10 g approx. / Cable 40 g approx.	80 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.
DPH-102-M5-R-C5	EMC Directive, RoHS Directive	Gauge pressure	0 to +1.000 MPa	1.5 MPa	Air, non-corrosive gas	12 to 24 V DC ± 10 % Ripple P-P 10 % or less	15 mA or less	Output voltage : 1 to 5 V (over rated pressure range) Zero point : within 1 V ± 2.5 % F.S. (vacuum / positive pressure type) within 3 V ± 3 % F.S. (compound pressure type) Span : within 4 V ± 3.5 % F.S. Linearity : within ±0.5 % F.S. Output impedance : 1 kΩ approx.	IP40 (IEC)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage : -10 to +60 ℃ +14 to +140 ℉	35 to 85 % RH, Storage : 35 to 85 % RH	1,000 V AC for one min. between all supply terminals connected together and enclosure	50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, amplitude 3 mm 0.118 in or maximum acceleration 196 m/s², in X, Y and Z directions for two hours each	1,000 m/s² acceleration (100 G approx.) in X, Y and Z directions for three times each	Over ambient temperature range 0 to +50 ℃ +32 to +122 ℉ : within ±2 % F.S. of detected pressure at +25 ℃ +77 ℉	M5 male thread (for installing gasket)	Front case : PBT, Rear case : PBT (glass fiber reinforced), Pressure port : Stainless steel (SUS303), O-ring : NBR Pressure element : Silicon diaphragm, PPS	Connector	0.2 mm² 4-core oil resistant cabtyre cable (Models with "-R" affixed to the Model No. have bending-resistant, oil-resistant cabtyre cable)	Extension up to total 10 m 32.808 ft is possible with 0.2 mm², or more, cable.	Head 6 g approx. / Cable 40 g approx.	70 g approx.	Connector (e-CON) : 1 pc.	Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +25 ℃ +77 ℉. The sensor head can be used independently.

Head-separated Dual Display Digital Pressure Sensor [For Gas] DPS-400 / DPH-100

Part Number List