The NA40 General Purpose Area Sensor from Panasonic offers a slim body design, failure monitoring and easy modification of length with robust aluminum enclosure.
40 mm Beam Pitch General Purpose Area Sensor NA40
Part number list
Results 37
Models table for series 40 mm Beam Pitch General Purpose Area Sensor NA40
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
630 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 30 mA or less Receiver: 60 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
800 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 35 mA or less Receiver: 115 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
2,190 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 30 mA or less Receiver: 60 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
630 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 30 mA or less Receiver: 60 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
500 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
500 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 35 mA or less Receiver: 115 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
1,840 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
630 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 30 mA or less Receiver: 60 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
800 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 35 mA or less Receiver: 115 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
2,190 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 30 mA or less Receiver: 60 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
630 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 30 mA or less Receiver: 60 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
500 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
Extension up to total 100 m 328.084 ft is possible, for both emitter and receiver, with 0.5 mm2, or more, cable. (However, the interference prevention wire can extend up to 20 m 65.617 ft between two emitters.)
500 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Emitter: 35 mA or less Receiver: 115 mA or less
NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between sensing output and 0 V) • Residual voltage: 1.6 V or less (at 100 mA sink current)
ON when all beam channels are received / OFF when one or more beam channels are interrupted
Incorporated
NPN open-collector transistor • Maximum sink current: 50 mA • Applied voltage: 30 V DC or less (between self-diagnosis output and 0 V) • Residual voltage: 1.6 V or less (at 50 mA sink current)
OFF when unstable light received condition continues for 5 sec. or more, or the output transistor fails
Incorporated
12 ms or less
Incorporated (Two units of sensors can be mounted close together.)
Incorporated with the three color indicators on the receiver • Sensing output operation indicator: Red LED (lights up when one or more beam channels are interrupted) • Stable incident beam indicator: Green LED (lights up when all beam channels are received stably) • Unstable incident beam indicator: Yellow LED (lights up when one or more beam channels are received unstably) * When the output transistor fails, the three color indicators blink simultaneously.
IP65 (IEC)
–10 to +50 ℃ +14 to +122 ℉ (No dew condensation or icing allowed), Storage: –10 to +60 ℃ +14 to +140 ℉
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,500 ℓx or less at the light-receiving face
1,000 V AC for one min. between all supply terminals connected together and enclosure
20 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
10 to 55 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Infrared LED (synchronized scanning system)
Protection enclosure: Aluminum Unit case: ABS Front cover: Acrylic Lens: Acrylic
0.5 mm2 4-core (emitter: 3-core) cabtyre cable, 0.5 m 1.640 ft long, with a round connector at the end * Use together with the optional mating cable
1,840 g approx.
MS-NA40-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc.