HG-S1110R
Specification
| Item | Performance characteristics |
|---|---|
| CE Marking Directive Compliance | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) |
| Applicable Controller | HG-SC101(-P), HG-SC111(-P), HG-SC112(-P), HG-SC113 |
| Position Detection Method | Optical absolute linear encoder method |
| Measuring Range | 10 mm 0.394 in |
| Travel (mm) | 10.5 mm 0.413 in or more |
| Measuring Force: Downward Mount | 0.35 N or less 0.30 N (Note 1): In the case of low measurement force type (HG-S1010R / HG-S1110R), measurements were obtained with products in standard configuration without rubber bellows. (Note 2): Typical value near center of measurement. |
| Measuring Force: Upward Mount | - |
| Measuring Force: Side Mount | 0.25 N or less 0.20 N (Note 1): In the case of low measurement force type (HG-S1010R / HG-S1110R), measurements were obtained with products in standard configuration without rubber bellows. (Note 2): Typical value near center of measurement. |
| Resolution | 0.1 μm 0.004 mil |
| Sampling Rate | 1ms |
| Indication Accuracy (P-P) | Full range: 1.0 μm 0.039 mil or less Narrow range: 0.5 μm 0.020 mil or less (any 60 μm 2.362 mil) |
| Tip Deviation Amount | 35 μm 1.378 mil (typical)(Note):Linearity F.S. = 16 mA, and is linearity with respect to digitally measured values. |
| Hot Swap Function | Incorporated |
| Operation Indicator | 2-color LED (Orange / Green) |
| Environmental Resistance: Protection | - |
| Environmental Resistance: Ambient Temperature | -10 to +55 ℃ +14 to +131 ℉ (No condensation or icing), Storage: -20 to +60 ℃ -4 to +140 ℉ |
| Environmental Resistance: Ambient Humidity | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Insulation Resistance | 100 MΩ or more at 250 V DC |
| Environmental Resistance: Vibration Resistance | 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each |
| Environmental Resistance: Shock Resistance | 1,960 m/s2acceleration in X, Y and Z directions three times each |
| Mounting Nut Tightening Strength | 12.5N・m |
| Probe Tightening Torque | 0.1 to 0.4 N・m (no force applied to main unit) |
| Grounding Method | Capacitor grounding |
| Material | Body: Zinc, Holder: Stainless steel, Spindle: Tool steel, Probe※: Brass (body) / Ceramic (ball), Rubber bellows: NBR (black) ※The probes (optional) are also available. |
| Weight (Typ.) | Net weight: 80 g approx. |
| Accessory | Low measuring force type (HG-S1010R / HG-S1110R): Sensor head fastening wrench 1 pc., Mounting nut 1 pc., Rubber bellows 1 pc. |
| Remark | Where measurement conditions have not been specified precisely, the conditions used were as follows: standard type measurement probe (HG-SS10C), ambient temperature +20 ℃ +68 ℉, and a clean atmosphere where dust and liquids such as water and oil do not come in contact with the equipment. |
| Pollution Degree | 2 |
| Operating Altitude | 2,000 m 6561.68 ft or less (Note) : Do not use or store in an environment that has been pressurized to an air pressure higher than the atmospheric pressure at 0 m. |
Stock Check
Important
The service is owned, operated, controlled and managed by Panasonic's distributors.
For pricing, delivery and technical questions related to this service, please direct to them.
Panasonic assumes no responsibility for any dealings you may have with distributors.
