Ultra-compact Laser Collimated Beam Sensor HL-T1

The HL-T1 Sensor is an ultra-small laser Thru-Beam Sensor with very high resolution.

Three different types are available: HL-T1001F with a 1mm laser beam which is able to detect object 8µm in diameter at a distance of 500mm between receiver and transmitter; HL-T1005F and HL-T1010F with a laser collimator which produces a light curtain of 5mm or 10mm width respectively. The red Semiconductor LED, which belongs to Laser Class 1, makes it possible to use HL-T1 without any safety requirements.

Characteristics

Resolution Max. 4µm
Red Light Semiconductor LED Belongs To Laser Class 1
Sensing Range Up To 2m (HL-T1001F)
Minimum Sensing Object 8µm Diameter (HL-T1001AF)
Compact Design

Models table for series Ultra-compact Laser Collimated Beam Sensor HL-T1
Part No.	Type	CE Marking Directive Compliance	Applicable Controller	Sensing Range	Emission Indicator	Interference Prevention Function	Applicable Sensor Head	Supply Voltage	Current Consumption	Measuring Cycle	Linear Output	Linear Output: Temperature Characteristics	Settable Average Sampling Rate	Judgment Outputs (HIGH, PASS, LOW)	Judgment Outputs (HIGH, PASS, LOW): Utilization Category	Judgment Outputs (HIGH, PASS, LOW): Number of Outputs	Judgment Outputs (HIGH, PASS, LOW): Output Operation	Judgment Outputs (HIGH, PASS, LOW): Short-Circuit Protection	Laser Off Input	Zero Reset Input	Timing Input	Reset Input	Indicators: Laser Emitting (LD ON)	Indicators: Judgment Outputs	Indicators: Enable	Indicators: Zero Reset (Zero)	Main Digital Display	Sub-Digital Display	Main Functions	Pollution Degree	Environmental Resistance: Ambient Temperature	Environmental Resistance: Ambient Humidity	Environmental Resistance: Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Environmental Resistance: Vibration Resistance	Environmental Resistance: Shock Resistance	Emitting Element: IEC/JIS Standards Conforming Type	Emitting Element: FDA Regulations Conforming Type	Material	Cable	Cable Extension	I/O Cable	I/O Cable Extension	Weight (Typ.)	Accessory
HL-T1001A	Beam diameter dia.1 mm dia.0.039 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1010A	Sensing width 10 mm 0.394 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 30 g approx. Receiver: 20 g approx.	MS-LA3-1 (Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1 (Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1005A	Sensing width 5 mm 0.197 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-AC1P	PNP output	EMC Directive, RoHS Directive					HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	190 mA or less (when connected to the sensor head)	150 micro s	Current / voltage output switchable (Note) -During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm -During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm (In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.) (Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller.	plus or minus 0.2 % F.S./℃ (Note) These are the temperature characteristics of the linear output when the sensor head is connected.	1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096 (Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1).	PNP open-collector transistor -Maximum source current: 50 mA -Applied voltage: 30 V DC or less (between judgment output and +V) -Residual voltage: 2 V or less (at 50 mA source current)	DC-12 or DC-13	HIGH / PASS / LOW 3 values output	HIGH: ON when measured value > HIGH threshold value PASS: ON when HIGH threshold value >= measured value >= LOW threshold value LOW: ON when LOW threshold value > measured value	Incorporated	+V connection: Laser emission halt Open: Laser emission -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	+V connection: Zero reset operates Open: Zero reset ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	+V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	+V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	Green LED (lights up during laser emission)	HIGH: Orange LED (lights up when measured value > HIGH threshold value) PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value) LOW: Yellow LED (lights up when LOW threshold value > measured value)	Green LED (lights up during normal operation)	Green LED (lights up when the zero reset function is enabled)	5 digit red LED display [RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.]	5 digit yellow LED display [RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.]	・Measured value display ・Setting value, light amount value resolution display ・Standard received light setting ・Automatic scaling ・Scaling ・Display reverse ・ECO display ・Display digits limitation ・Sample hold ・Peak hold ・Bottom hold ・Peak to peak hold ・Self peak hold ・Self bottom hold ・Zero reset ・Initial reset ・ON-delay timer ・OFF-delay timer ・One-shot timer ・Differentiation ・Sensitivity selection ・Threshold value direct setting ・Positioning teaching ・2-point teaching ・Automatic teaching ・Hysteresis width variability ・Monitor focus ・Non-measuring time setting ・(A – B) calculation(Note：The calculation unit is necessary.) ・(A + B) calculation(Note：The calculation unit is necessary.) ・Mutual interference prevention (Note：The calculation unit is necessary.) ・Laser deterioration detection ・Key lock ・Zero reset memory	3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH		1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.7 mm 0.028 in double amplitude in X, Y and Z directions for 80 min.	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each			Enclosure: Polybutylene terephthalate Transparent cover: Polycarbonate			0.09 mm² 10-core composite cable, 2 m 6.562 ft long	Extension up to total 10 m 32.808 ft is possible, with 0.09 mm² or more, cable. (Note) If the extension cable is longer than 10 m 32.808 ft, then it will not qualify for CE marking.	Net weight: 140 g approx.
HL-AC1	NPN output	EMC Directive, RoHS Directive					HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	190 mA or less (when connected to the sensor head)	150 micro s	Current / voltage output switchable (Note) -During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm -During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm (In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.) (Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller.	plus or minus 0.2 % F.S./℃ (Note) These are the temperature characteristics of the linear output when the sensor head is connected.	1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096 (Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1).	NPN open-collector transistor -Maximum sink current: 50 mA -Applied voltage: 30 V DC or less (between judgment output and 0 V) -Residual voltage: 1.2 V or less (at 50 mA sink current)	DC-12 or DC-13	HIGH / PASS / LOW 3 values output	HIGH: ON when measured value > HIGH threshold value PASS: ON when HIGH threshold value >= measured value >= LOW threshold value LOW: ON when LOW threshold value > measured value	Incorporated	0 V connection: Laser emission halt Open: Laser emission -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	0 V connection: Zero reset operates Open: Zero reset ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	0 V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	0 V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	Green LED (lights up during laser emission)	HIGH: Orange LED (lights up when measured value > HIGH threshold value) PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value) LOW: Yellow LED (lights up when LOW threshold value > measured value)	Green LED (lights up during normal operation)	Green LED (lights up when the zero reset function is enabled)	5 digit red LED display [RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.]	5 digit yellow LED display [RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.]	・Measured value display ・Setting value, light amount value resolution display ・Standard received light setting ・Automatic scaling ・Scaling ・Display reverse ・ECO display ・Display digits limitation ・Sample hold ・Peak hold ・Bottom hold ・Peak to peak hold ・Self peak hold ・Self bottom hold ・Zero reset ・Initial reset ・ON-delay timer ・OFF-delay timer ・One-shot timer ・Differentiation ・Sensitivity selection ・Threshold value direct setting ・Positioning teaching ・2-point teaching ・Automatic teaching ・Hysteresis width variability ・Monitor focus ・Non-measuring time setting ・(A – B) calculation(Note：The calculation unit is necessary.) ・(A + B) calculation(Note：The calculation unit is necessary.) ・Mutual interference prevention (Note：The calculation unit is necessary.) ・Laser deterioration detection ・Key lock ・Zero reset memory	3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH		1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.7 mm 0.028 in double amplitude in X, Y and Z directions for 80 min.	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each			Enclosure: Polybutylene terephthalate Transparent cover: Polycarbonate			0.09 mm² 10-core composite cable, 2 m 6.562 ft long	Extension up to total 10 m 32.808 ft is possible, with 0.09 mm² or more, cable. (Note) If the extension cable is longer than 10 m 32.808 ft, then it will not qualify for CE marking.	Net weight: 140 g approx.
HL-T1005F	Sensing width 5 mm 0.197 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1010F	Sensing width 10 mm 0.394 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 30 g approx. Receiver: 20 g approx.	MS-LA3-1 (Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1 (Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1001F	Beam diameter dia.1 mm dia.0.039 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set

Models table for series Ultra-compact Laser Collimated Beam Sensor HL-T1
Part No.	Type	CE Marking Directive Compliance	Applicable Controller	Sensing Range	Emission Indicator	Interference Prevention Function	Applicable Sensor Head	Supply Voltage	Current Consumption	Measuring Cycle	Linear Output	Linear Output: Temperature Characteristics	Settable Average Sampling Rate	Judgment Outputs (HIGH, PASS, LOW)	Judgment Outputs (HIGH, PASS, LOW): Utilization Category	Judgment Outputs (HIGH, PASS, LOW): Number of Outputs	Judgment Outputs (HIGH, PASS, LOW): Output Operation	Judgment Outputs (HIGH, PASS, LOW): Short-Circuit Protection	Laser Off Input	Zero Reset Input	Timing Input	Reset Input	Indicators: Laser Emitting (LD ON)	Indicators: Judgment Outputs	Indicators: Enable	Indicators: Zero Reset (Zero)	Main Digital Display	Sub-Digital Display	Main Functions	Pollution Degree	Environmental Resistance: Ambient Temperature	Environmental Resistance: Ambient Humidity	Environmental Resistance: Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Environmental Resistance: Vibration Resistance	Environmental Resistance: Shock Resistance	Emitting Element: IEC/JIS Standards Conforming Type	Emitting Element: FDA Regulations Conforming Type	Material	Cable	Cable Extension	I/O Cable	I/O Cable Extension	Weight (Typ.)	Accessory
HL-T1001A	Beam diameter dia.1 mm dia.0.039 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1010A	Sensing width 10 mm 0.394 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 30 g approx. Receiver: 20 g approx.	MS-LA3-1 (Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1 (Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1005A	Sensing width 5 mm 0.197 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-AC1P	PNP output	EMC Directive, RoHS Directive					HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	190 mA or less (when connected to the sensor head)	150 micro s	Current / voltage output switchable (Note) -During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm -During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm (In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.) (Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller.	plus or minus 0.2 % F.S./℃ (Note) These are the temperature characteristics of the linear output when the sensor head is connected.	1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096 (Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1).	PNP open-collector transistor -Maximum source current: 50 mA -Applied voltage: 30 V DC or less (between judgment output and +V) -Residual voltage: 2 V or less (at 50 mA source current)	DC-12 or DC-13	HIGH / PASS / LOW 3 values output	HIGH: ON when measured value > HIGH threshold value PASS: ON when HIGH threshold value >= measured value >= LOW threshold value LOW: ON when LOW threshold value > measured value	Incorporated	+V connection: Laser emission halt Open: Laser emission -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	+V connection: Zero reset operates Open: Zero reset ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	+V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	+V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	Green LED (lights up during laser emission)	HIGH: Orange LED (lights up when measured value > HIGH threshold value) PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value) LOW: Yellow LED (lights up when LOW threshold value > measured value)	Green LED (lights up during normal operation)	Green LED (lights up when the zero reset function is enabled)	5 digit red LED display [RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.]	5 digit yellow LED display [RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.]	・Measured value display ・Setting value, light amount value resolution display ・Standard received light setting ・Automatic scaling ・Scaling ・Display reverse ・ECO display ・Display digits limitation ・Sample hold ・Peak hold ・Bottom hold ・Peak to peak hold ・Self peak hold ・Self bottom hold ・Zero reset ・Initial reset ・ON-delay timer ・OFF-delay timer ・One-shot timer ・Differentiation ・Sensitivity selection ・Threshold value direct setting ・Positioning teaching ・2-point teaching ・Automatic teaching ・Hysteresis width variability ・Monitor focus ・Non-measuring time setting ・(A – B) calculation(Note：The calculation unit is necessary.) ・(A + B) calculation(Note：The calculation unit is necessary.) ・Mutual interference prevention (Note：The calculation unit is necessary.) ・Laser deterioration detection ・Key lock ・Zero reset memory	3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH		1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.7 mm 0.028 in double amplitude in X, Y and Z directions for 80 min.	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each			Enclosure: Polybutylene terephthalate Transparent cover: Polycarbonate			0.09 mm² 10-core composite cable, 2 m 6.562 ft long	Extension up to total 10 m 32.808 ft is possible, with 0.09 mm² or more, cable. (Note) If the extension cable is longer than 10 m 32.808 ft, then it will not qualify for CE marking.	Net weight: 140 g approx.
HL-AC1	NPN output	EMC Directive, RoHS Directive					HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F	12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less	190 mA or less (when connected to the sensor head)	150 micro s	Current / voltage output switchable (Note) -During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm -During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm (In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.) (Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller.	plus or minus 0.2 % F.S./℃ (Note) These are the temperature characteristics of the linear output when the sensor head is connected.	1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096 (Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1).	NPN open-collector transistor -Maximum sink current: 50 mA -Applied voltage: 30 V DC or less (between judgment output and 0 V) -Residual voltage: 1.2 V or less (at 50 mA sink current)	DC-12 or DC-13	HIGH / PASS / LOW 3 values output	HIGH: ON when measured value > HIGH threshold value PASS: ON when HIGH threshold value >= measured value >= LOW threshold value LOW: ON when LOW threshold value > measured value	Incorporated	0 V connection: Laser emission halt Open: Laser emission -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	0 V connection: Zero reset operates Open: Zero reset ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	0 V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	0 V connection: Effective Open: Ineffective -Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)	Green LED (lights up during laser emission)	HIGH: Orange LED (lights up when measured value > HIGH threshold value) PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value) LOW: Yellow LED (lights up when LOW threshold value > measured value)	Green LED (lights up during normal operation)	Green LED (lights up when the zero reset function is enabled)	5 digit red LED display [RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.]	5 digit yellow LED display [RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.]	・Measured value display ・Setting value, light amount value resolution display ・Standard received light setting ・Automatic scaling ・Scaling ・Display reverse ・ECO display ・Display digits limitation ・Sample hold ・Peak hold ・Bottom hold ・Peak to peak hold ・Self peak hold ・Self bottom hold ・Zero reset ・Initial reset ・ON-delay timer ・OFF-delay timer ・One-shot timer ・Differentiation ・Sensitivity selection ・Threshold value direct setting ・Positioning teaching ・2-point teaching ・Automatic teaching ・Hysteresis width variability ・Monitor focus ・Non-measuring time setting ・(A – B) calculation(Note：The calculation unit is necessary.) ・(A + B) calculation(Note：The calculation unit is necessary.) ・Mutual interference prevention (Note：The calculation unit is necessary.) ・Laser deterioration detection ・Key lock ・Zero reset memory	3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH		1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure	10 to 150 Hz frequency, 0.7 mm 0.028 in double amplitude in X, Y and Z directions for 80 min.	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each			Enclosure: Polybutylene terephthalate Transparent cover: Polycarbonate			0.09 mm² 10-core composite cable, 2 m 6.562 ft long	Extension up to total 10 m 32.808 ft is possible, with 0.09 mm² or more, cable. (Note) If the extension cable is longer than 10 m 32.808 ft, then it will not qualify for CE marking.	Net weight: 140 g approx.
HL-T1005F	Sensing width 5 mm 0.197 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1010F	Sensing width 10 mm 0.394 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.35 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 30 g approx. Receiver: 20 g approx.	MS-LA3-1 (Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1 (Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set
HL-T1001F	Beam diameter dia.1 mm dia.0.039 in type	EMC Directive, RoHS Directive	HL-AC1, HL-AC1P	■■【In the case of(0 to 500 mm 0 to 19.685 in)】■■ Sensing width: ø1 mm ø0.039 in Min. sensing object: ø8 micro m ø0.315 mil opaque object Repeatability (During the state in which light is half blocked): 4 micro m 0.157 mil (Note：In case of an average sampling rate of 64 times.) Linear output resolution: 4 micro m 0.157 mil (Note) In case of an average sampling rate of 64 times. (Note)Value calculated with the linear output allowance factor (plus or minus 3 sigma) when connected to the controller included in the calculation of the detection width. (Note：This value was obtained by converting the range of linear output fluctuation (plus or minus 3 sigma) into a sensing width, assuming that the smallest sensing object blocks the beam at the approximate center of the beam diameter of ø1 mm ø0.039 in.) ■■【In the case of (500 to 2,000 mm 19.685 to 78.74 in)】■■ Sensing width: ø1 to ø2.5 mm ø0.039 to ø0.098 in Min. sensing object: ø50 micro m ø1.969 mil opaque object Repeatability (During the state in which light is half blocked): - Linear output resolution: - -	Green LED (lights up during laser emission)	Two units of sensors can be mounted close together. (When the controller interference prevention function is used)																								3 (industrial environment)	0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 10,000 liter x or less at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	100 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each	300 m/s² acceleration (30 G approx.) in X, Y and Z directions three times each	Red semiconductor laser Class 1 (IEC / JIS) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil)	Red semiconductor laser Class II (FDA) (modulated, max. output: 0.2 mW, peak emission wavelength: 650 nm 0.026 mil) (IEC / JIS: Class 1)	Enclosure: Polyetherimide Case cover: Polycarbonate Front cover: Glass	0.09mm² 3-core shielded cable with connector, 0.5 m 1.640 ft long	Extension up to total 10 m 32.808 ft is possible, with the optional cable.			Emitter: 15 g approx. Receiver: 15 g approx.	MS-HLT1-1(Sensor head mounting bracket): One set of two brackets for both the emitter and the receiver CN-HLT1-1(Sensor head to controller connection cable): 1 cable Laser beam alignment sticker: 2 pcs. Label set (FDA regulations conformed type only): 1 set

What's New

Stay up to date

View All

HG-S Series Contact-Type Digital Displacement Sensor

Industrial Automation Icon

Ultra-compact Laser Collimated Beam Sensor HL-T1

Characteristics

Part Number List

What's New

Stay up to date

HG-S Series Contact-Type Digital Displacement Sensor