Ultra-minute Photoelectric Sensor EX-Z

At a thickness of 3mm, the EX-Z Series is one of the world's thinnest Photoelectric Sensors with a built-in amplifier which was achieved by utilizing a new Semiconductor packaging technology that does not use wire bonding. The compact design now makes it possible to install the sensors in narrow spaces that, in the past, could fit only a conventional fiber sensor head.

Models table for series Ultra-minute Photoelectric Sensor EX-Z
Part No.	CE Marking Directive Compliance	Output Operation	Sensing Range	Min. Sensing Object	Repeatability (Perpendicular to Sensing Axis)	Supply Voltage	Current Consumption	Output	Output: Short-Circuit Protection	Response Time	Operation Indicator	Stability Indicator	Protection	Ambient Temperature	Ambient Humidity	Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Emitting Element	Grounding	Material	Cable	Cable Extension	Weight (Typ.)	Accessory	Remark
EX-Z11A	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FA-P-R	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FA-R	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11B-R	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z12B-P	EMC Directive, RoHS Directive	Dark-ON	200 mm 7.874 in	ø0.5 mm ø0.02 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 200 mm 7.874 in)	0.03 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11B	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FB-P	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FB-R	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FA-P	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z12A	EMC Directive, RoHS Directive	Light-ON	200 mm 7.874 in	ø0.5 mm ø0.02 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 200 mm 7.874 in)	0.03 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.

Models table for series Ultra-minute Photoelectric Sensor EX-Z
Part No.	CE Marking Directive Compliance	Output Operation	Sensing Range	Min. Sensing Object	Repeatability (Perpendicular to Sensing Axis)	Supply Voltage	Current Consumption	Output	Output: Short-Circuit Protection	Response Time	Operation Indicator	Stability Indicator	Protection	Ambient Temperature	Ambient Humidity	Ambient Illuminance	Voltage Withstandability	Insulation Resistance	Vibration Resistance	Shock Resistance	Emitting Element	Grounding	Material	Cable	Cable Extension	Weight (Typ.)	Accessory	Remark
EX-Z11A	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FA-P-R	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FA-R	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11B-R	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z12B-P	EMC Directive, RoHS Directive	Dark-ON	200 mm 7.874 in	ø0.5 mm ø0.02 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 200 mm 7.874 in)	0.03 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11B	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FB-P	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FB-R	EMC Directive, RoHS Directive	Dark-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z11FA-P	EMC Directive, RoHS Directive	Light-ON	50 mm 1.969 in	ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 50 mm 1.969 in)	0.02 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	PNP open-collector transistor - Maximum source current: 20 mA - Applied voltage: 30 V DC or less (between output and +V) - Residual voltage: 1.5 V or less (at 20 mA source current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.
EX-Z12A	EMC Directive, RoHS Directive	Light-ON	200 mm 7.874 in	ø0.5 mm ø0.02 in opaque object (Completely beam interrupted object)(Setting distance between emitter and receiver: 200 mm 7.874 in)	0.03 mm 0.001 in or less	12 to 24 V DC ±10 % Ripple P-P 10 % or less	Emitter: 10 mA or less Receiver: 10 mA or less	NPN open-collector transistor - Maximum sink current: 20 mA - Applied voltage: 30 V DC or less (between output and 0 V) - Residual voltage: 1.5 V or less (at 20 mA sink current)	Incorporated	0.5 ms or less	Orange LED (Lights up when the sensing output is ON)	Green LED (Lights up under the stable light received condition or the stable dark condition)	IP67 (IEC)	-10 to +55 ℃ 14 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉	35 to 85 % RH, Storage: 35 to 85 % RH	Incandescent light: 5,000 ℓx at the light-receiving face	1,000 V AC for one min. between all supply terminals connected together and enclosure	20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure	10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each	500 m/s² acceleration (50 G approx.) in X, Y and Z directions for three times each	Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated)	Floating	Enclosure: PBT Lens: Polycarbonate Metallic part: Stainless steel (SUS304)(SUS301 for rear side of front sensing type)	0.1 mm² 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Note:The bending-resistant cable type has a 0.1 mm² 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable, 2 m 6.562 ft long.	Extension up to total 50 m 164 ft is possible with 0.3 mm², or more, cable (both emitter and receiver) .	Net weight (each emitter and receiver) : 15 g approx. Gross weight: 35 g approx.	M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ 73 ℉.

Ultra-minute Photoelectric Sensor EX-Z

Part Number List