Ultra-slim Safety door switch with solenoid interlock SG-B1
Extremely Think SG Series Safety Devices
Panasonic offers a large selection of Safety Devices: Switches for safety fence doors, Key Select Switches, Emergency Switches and enable Grip Switches. In addition, there are two Safety Control Units available, one for general purposes and one to control Safety Light Curtains.
The SG-B1 Series and the SG-A1 Series are among the world’s thinnest Safety Door Switches. The SG-B1 Series features a solenoid interlock and five built-in contacts. The SG-A1 Series Safety Door Switch comes with three built-in contacts.
Ultra-slim Safety door switch with solenoid interlock SG-B1
Part number list
Results 8
Models table for series Ultra-slim Safety door switch with solenoid interlock SG-B1
Part No.
Datasheet
Main Contacts
Door Monitor Contacts
Lock Monitor Contacts
Cable Length
Applicable Standards
Applicable Standards: Standards For Use
Applicable Directives
Operating Condition: Ambient Temperature
Operating Condition: Ambient Humidity
Operating Condition: Pollution Degree S
Operating Condition: Altitude
Rated Insulation Voltage (Ui)
Impulse Withstand Voltage (Uimp)
Thermal Current (Ith)
Rated Operational Voltage (Ue)/Rated Operational Current (Le)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)
・Ambient temperature : -25 to +35 ℃ -13 to +95 ℉ 2.5 A (up to 2 circuits) 1.0 A (3 or more circuits) ・Ambient temperature : 35 to +50 ℃ 95 to +122 ℉ 1.0 A (1 circuit) 0.5 A (2 or more circuits)
Ue
30V
125V
250V
Ie
Main circuit, look monitor circuit
AC
Resistive load (AC-12)
-
2A
-
Inductive load (AC-15)
-
1A
-
DC
Resistive load (DC-12)
2A
0.4A
-
Inductive load (DC-13)
1A
0.22A
-
Door monitor circuit
AC
Resistive load (AC-12)
-
2.5A
1.5A
Inductive load (AC-15)
-
1.5A
0.75A
DC
Resistive load (DC-12)
2.5A
1.1A
0.55A
Inductive load (DC-13)
2.3A
0.55A
0.27A
Class II (IEC 61140)(Note), 回(double insulated) (Note): Basic insulation of 2.5 kV, 1.5 kV impulse withstand voltage is ensured between different contact circuits and between contact circuits and LED or solenoid in the enclosure. When both SELV (safety extra low voltage) or PELV (protective extra low voltage) circuits and other circuits (such as 230 V AC circuits) are used for the solenoid power and contact circuits at the same time, the SELV or PELV requirements are not met any more.
900 operations/hour
0.05 to 1.0 m/sec.
2,000,000 (ISO 13849-1 Annex C Table C.1)
1,000,000 operations min. (GS-ET-19)
100,000 operations min. (900 operations/hour, AC-12 125 V 2A, DC-12 125 V 0.4 A) 1,000,000 operations min. (900 operations/hour, 24 V AC/DC 0.1 A resistive load)
500 N min. (GS-ET-19) (Note): The actuator locking strength is rated at 500 N of static load. Do not apply a load higher than the rated value. Do not apply a load higher than the rated value. When a higher load is expected to work on the actuator, provide an additional system consisting of another safety switch without lock (such as the SG-A1 safety switch) or a sensor to detect door opening and stop the machine.
8 mm 0.315 in min.
60 N min.
300 mΩ max. (initial value, 1 m 3.281 ft cable) 700 mΩ max. (initial value, 5 m 16.404 ft cable)
IP 67 (IEC 60529)
Malfunction : 100 m/s2, Destruction : 1,000 m/s2
Malfunction : 10 to 55 Hz, half amplitude 0.35 mm 0.014 in Destruction : 30 Hz, half amplitude 1.5 mm 0.059 in
Use 250 V / 10 A fast acting type fuse
Enclosure : PA66
UL style 2464, No.22 AWG 12-core
DC 24 V 100% duty cycle
110 mA (solenoid 100 mA, LED 10 mA : initial value)