LS-501P

Specifications table for model LS-501P
Item	Performance characteristics
CE Marking Directive Compliance	EMC Directive, RoHS Directive
Operation Indicator	Orange LED (lights up when sensing output 1 or sensing output 2 is ON)
Protection	IP40(IEC)
Ambient Temperature	-10 to +55degrees + 14 to 131 degrees Fahrenheit (If 4 to 7 units are mounted close together, -10 to +50 degrees +14 to +122 degrees Fahrenheit ; if 8 to 16 units are mounted close together, -10 to +45 degrees +14 to +113 degrees Fahrenheit )(No dew condensation or icing allowed), Storage: -20 to +70 degrees -4 to +158 degrees Fahrenheit
Ambient Humidity	35 to 85 % RH, Storage: 35 to 85 % RH
Voltage Withstandability	1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation Resistance	20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration Resistance	10 to 150 Hz frequency, 0.75 mm 0.030 in (max. 10 G) amplitude in X, Y and Z directions for two hours each
Shock Resistance	98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each
Material	Enclosure: Polycarbonate Cover: Polycarbonate Switch: Polyacetal
Cable	-
Weight (Typ.)	Net weight: 15 g approx. Gross weight: 55 g approx.
Accessory	FX-MB1 (Amplifier protective seal): 1 set
Supply Voltage	12 to 24 V DC +10-15% Ripple P-P 10 % or less
Power Consumption	Normal operation: 1,200 mW or less (Current consumption 50 mA or less at 24 V supply voltage) ECO mode: 980 mW or less (Current consumption 40 mA or less at 24 V supply voltage)
Sensing Outputs (Sensing Output 1, 2)	PNP open-collector transistor ・Maximum source current: 50 mA (Note：25 mA if 5 or more amplifier are connected in cascade (excluding cable extension).) ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 2 V or less (at max. source current) (Note：Select either sensing output 2 or external input as the connector type.)
Sensing Outputs (Sensing Output 1, 2): Output Operation	Selectable either Light-ON or Dark-ON
Sensing Outputs (Sensing Output 1, 2): Short-Circuit Protection	Incorporated
Sensing Output Setting: Sensing Output 1	Normal mode, differential mode, hysteresis mode, window comparator mode, selectable
Sensing Output Setting: Sensing Output 2	Normal mode, differential mode, hysteresis mode, self-diagnostic output mode, selectable (Note：Select either sensing output 2 or external input.)
Response Time	H-SP: 60 micro s or less, FAST: 150 micro s or less, STD: 250 micro s or less, LONG: 500 micro s or less, U-LG: 5 ms or less, HYPR: 24 ms or less selectable
Monitor Current Output	-
External Input	PNP non-contact input - Signal condition High: +4 Vto+V DC(sink current 3.0 mA or less), Low: 0 to +0.6 V DC or open - Input impedance: 10 kOhm approx. (Note：Select either sensing output 2 or external input.)
External Input Function	Laser emission halt / teaching (full-auto teaching, limit teaching, 2 point teaching) / logic operation setting / copy lock /display adjustment / data bank load / data bank save, selectable
Laser Emission Indicator	Green LED (lights up during laser emission)
Output select Indicator	Yellow LED (lights up when output is selected)
Digital Display	8-digit 7-segment digital display (4-digit green LED + 4-digit red LED), MODE indicator (Yellow LED): L/D, CUST, PRO
Incident Light Indication Range	H-SP/FAST/STD: 0 to 4,000 LONG/U-LG/HYPR: 0 to 9,999
Sensitivity Setting	2-level teaching / limit teaching / full auto teaching / manual adjustment
Logical Operation	Between sensing output 1 and calculation target: Disabled / and / or / xor, selectable Calculation target: Sensing output 2 / adjacent upstream amplifier (sensing output 1) / external input, selectable
Timer Function	OFF-delay timer, ON-delay timer, ONE-SHOT timer, ON / OFF-delay timer, ON-delay / ONE-SHOT timer, switchable either effective of ineffective, with variable timer period OFF-delay timer, ON-delay timer, ONE-SHOT timer, switchable either effective of ineffective, with variable timer period
Timer Function: Time	Timer range '' ms'': 0.5 ms approx., 1 to 9,999 ms approx., in approx. 1 ms intervals Timer range '' sec'': 0.5 sec. approx., 1 to 32 sec. approx., in approx. 1 sec. intervals Timer range '' 1/10 ms'': 0.05 ms approx., 0.1 to 999.9 ms approx., in approx. 0.1 ms intervals, Set separately for each output.
Automatic Interference Prevention Function	Incorporated (Note：Number of units that can be mounted close together: 0 for H-SP; 2 for FAST; 4 for STD, LONG, U-LG, or HYPR)
Cable Extension	Extension up to total 100 m 328.084 ft is possible with 0.3mm2, or more, cable.