DPH-L114
Specification
| Item | Performance characteristics |
|---|---|
| CE Marking Directive Compliance | EMC Directive, RoHS Directive |
| Type of Pressure | Sealed gauge pressure (Note): The sensor's internal mechanism is sealed based on an air pressure of 1,013 hPa. |
| Rated Pressure Range | 0 to +10 MPa |
| Pressure Withstandability | 20 MPa |
| Applicable Fluid | Gases and fluids that do not corrode stainless steel SUS630, SUS304, or SUSXM7 |
| Supply Voltage | 9 to 36 V DC [9 to 32 V DC when using the attached connector (e-CON)] |
| Current Consumption | 20 mA or less |
| Analog Voltage Output | Output voltage: 1 to 5 V DC (over rated pressure range) Accuracy: ±1.0 % F.S. (at 23 ±2 ℃ +73.4 ±35 ℉) ±2.0 % F.S. (at -20 to 125 ℃ -4 to +257 ℉) (including linearity, hysteresis and repeatability) |
| Response Time | 1 ms or less |
| Protection | IP67 (IEC) |
| Ambient Temperature | -20 to +80 ℃ (Pressure port: -20 to +125 ℃ -4 to +257 ℉, No dew condensation or icing allowed), Storage: -30 to +100 ℃ -22 to +212 ℉ [e-CON connector (accesory): -20 to +75 ℃ -4 to +167 ℉ (Storage: -30 to +75 ℃ -22 to +167 ℉)] |
| Ambient Humidity | 35 to 85 % RH, Storage : 35 to 85 % RH |
| Medium Temperature Range | -20 to +125 ℃ -4 to +257 ℉ |
| Voltage Withstandability | 150 V AC for one min. between all supply terminals connected together and enclosure |
| Insulation Resistance | 100 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure |
| Vibration Resistance | 10 to 2,000 Hz frequency, acceleration 200 m/s2, in X direction for four hours, in Y and Z directions for two hours each (Note): The X, Y, and Z directions are defined as follows :  |
| Shock Resistance | 1,000 m/s2 acceleration in X, Y and Z directions three times each |
| Grounding Method | Capacitor earth (Enclosure-supply terminal) |
| Pressure Port | R1/4 male thread (throttle embeded) |
| Material | Diaphragm : Stainless steel (SUS603), Pressure port : Stainless steel (SUS304), Throttle : Stainless steel (SUSXM7) |
| Connecting Method | Connector |
| Cable | 0.2 mm2 3-core heat resistant cabtyre cable 2 m 3.562 ft long |
| Cable Extension | Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable. |
| Weight (Typ.) | Net weight : 100 g approx., Gross weight : 150 g approx. |
| Accessories | Connector (e-CON) : 1 pc. |
| Remark | Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉. The sensor head can be used independently. Oil is used in the factory inspection process for models DPH-L114 and DPH-L154. There may be some residual oil inside the pressure port. |
| Dummy | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) |
Stock Check
What's New
Stay up to date
Latest Videos
Playlist
Sensors
PIR Motion Sensors (PAPIRS)
Sensors Icon